Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Be sure to tighten the stand fixing screw securely. If it remain loose, double triggering may occur. Rod Tighten Loosen When attaching the PDX-8 to a tom stand, check the dimensions of the rod. Depending on the dimensions of the rod, it may not be possible to attach the pad to the stand. Acceptable rod diameters: 9–11.5 mm (3/8 to 1/2 inch) Connecting To A Percussion Sound Module Use the included stereo cable to make connections. • If you use a monaural cable, you won’t be able to employ rim shot and cross stick playing techniques. • Connect the L-shaped plug of the included cable to the PDX-8. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 4 Trigger Settings For Percussion Sound Module Trigger Settings For Percussion Sound Module . Be sure to make these settings to ensure that the PDX-8 performs properly. Below you will find the settings recommended for different percussion sound modules. For instructions on setting the trigger parameters, refer to the Owner's Manual for your percussion sound module. * Leave the initial Cross Stick Cancel settings for each module unchanged. About the Head Tension Tighten the head so that the tension is rather firm. Looseness in the head tension may result in problems such as failure of the PDX-8’s rim shots to sound or double triggering. About Rim Sens (*1) If any of the following problems occurs, adjust Rim Sens to a value in the range indicated in the column for the corresponding percussion sound module. • If the rim sound plays even when you strike the head, lower the Rim Sens value. • If no rim sound plays even when the rim is struck forcefully, increase the Rim Sens value. * When using the TD-12 and TD-20, adjust the “RimShot Adjust.” TD-3 (Percussion Sound Module) IMPORTANT: Only the snare input is capable of producing a rim shot. Trigger Type ( ) 80r Mask Time ( ) 8 Rim Sensitivity ( ) 10 (7–12) (*1) TD-6V (Percussion Sound Module) IMPORTANT: Only the 2(snare) input is capable of producing a rim shot. TrigTyp PD-80R Mask Time 8ms Rim Sens 11 (8–13) (*1) TD-12/TD-20 (Percussion Sound Module) IMPORTANT: Only the inputs listed below are capable of producing a rim shot. TD-12: 2 (SNARE), 3–5 (TOM1–3), 11–12 (AUX1–2) TD-20: 2 (SNARE), 3–6 (TOM1–4), 12–15 (AUX1–4) Trig Type PD80R or PD85 Sensitivity 7 RimShot Adjust 2.0 (1.6–2.4) (*1) Setting when connecting with trigger input 2(SNARE) The PDX-8 does not support the TD-12’s and TD-20’s positional sensing. Set the TD-12/TD-20 so that strike position sensing is not activated. Set Snare CC to “OFF.” (press [SETUP], then [F1 (MIDI)], then [F3 (CTRL)]) 5 Playing Methods Playing Methods Head * Do not strike the hoop. Rim Shots Rim * To play rim shots, strike the rim in the area shown in the diagram. Cross Stick Only strike the rim of the pad. Depending on the instrument assigned to the rim, you can play rim shots and/or cross stick sounds. Rim Rim * To play the cross stick, be sure that you only strike the rim of the pad. Placing your hand on the head of the pad might prevent the cross stick sound from being played properly. * For more on settings and instruments, see the respective module’s owner’s manual. Player Suitable position for rim shots 6 Head Replacement Head Replacement The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): MH-8 Mesh Head Replacing the Head 1. Remove all tuning bolts from the PDX-8. Tuning Key Hoop Head Hoop’s Rubber Portion Head Sensor Rim Sensor Loosen Tighten Shell Tuning Bolt Do not apply excessive force to the sensor and cushion located under the head. Doing so can interfere with accurate detection, and may damage it. 2. Remove the hoop. 3. Remove the old head. 4. Place the new head on the shell. 5. Place the hoop onto the head. 6. Attach the tuning bolts to the hoop and shell. 7. Next, adjust the tension of the head. Refer to “Adjusting the Head Tension” (p. 4). Do not firmly tighten a single tuning bolt by itself. Doing so will make it impossible to tension the head evenly, and will cause malfunctions. Specifications PDX-8 Head Size: 8 inches Triggers: 2 (Head, Rim) Dimensions: 266 (W) x 326 (D) x 62 (H) mm 10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches Weight: 1.3 kg 2 lbs 14 oz Accessories: Owner’s Manual, Connection Cable, Tuning Key Options: Mesh Head (MH-8), Pad Mount (MDH-10U), Drum Stands (MDS-3C, MDS-6C, MDS-12, MDS-20) * In the interest of product improvement, the specifications and/ or appearance of this unit are subject to change without prior notice. * The Rim rubber is one component that eventually wears out (the more so if numerous rim shots are performed), and will require replacement. Rim shots may not be performed correctly when the rim rubber is worn out. If this occurs, replac...