Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
All other servicing should be referred to qualified service personnel. SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTION This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric shock. This product is equipped with a cord having an equipment-grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER — Improper connection ol the equipment-grounding conductor can result in a risk of electric chock. Check with a qualified electrician or servicemen if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product — if it will not fit the outlet, have a proper outlet installed by a qualified electrician. WARNING THIS APPARATUS MUST BE EARTH GROUNDED. The three conductors of the mains lead attached to this apparatus are identified with color as shown in the table below, together with the matching terminal on the UK type power plug. When connecting the mains lead to a plug, be sure to connect each conductor to the correct terminal, as indicated "This instruction applies to the product for United Kingdom." MAINS LEADS PLUG Conductor Color Mark on the matching terminal Live Brown fled or ietler L Neutral Blue Black or letter N Grounding Green- Yellow Green, Green-Yellow, letter E or symbol ■ CONNECTION to MIC to INST Keyboard, etc. О о о 00° Mil о о о о a a o cn CD /~ч □ □ □ CD CD W Tape Deck to LINE MT-32 в=ю В=Ю :.................. ,i ТТЛ I I CD Player * Inputs, INST and LINE, can be used at the same time. Input the signals of Lch and Rch to the INST and the LINE respectively when playing a stereo source in monaural. The devices to be connected to Inputs INST or LINE cannot be connected to the Input MIC. ■ OPERATION © Set the Input Volume Knob on the front © Push the Power Switch to turn the unit on. panel fully counterclockwise (minimum) and set the low Boost and the High Boost © Slowly rotate the Volume Knob clockwise Knobs at the center positions. until you get a desired volume. LOW HIGH INPUT BOOST BOOST VOLUME @ Connect electronic musical instruments and/or audio equipment to the Input Jacks on the rear panel. © Make sure that the unit is turned off, and connect the AC plug to an outlet. * This knob is provided for controlling the overall volume, not for controlling the volumes of the three inputs. When using more than one device at the same time, control the volume balance by adjusting the volume of each device. * Feeding the signal through a microphone may cause howling. If so, please rotate the Volume Knob counterclockwise, or move the microphone away from the unit. © Adjust the Low Boost and the High Boost Knobs to make a desired sound. ■ IMPORTANT NOTES ■ SPECIFICATIONS • Operating the unit near neon or fluorescent lamp may cause noise interference. If so, change the position or the angle of the units. Placing the musical instruments too close to each other may also cause noise. • Do not connect or disconnect to the plug with the unit switched on, to protect the speaker from excessive strain. • When setting up a musical instrument with the unit, connect the connection cord to the musical instrument first, then to the unit. When disconnecting, pull out the cord from the unit first, then from the musical instrument. • Avoid giving a strong shock to the unit and do not move it while it is being operated. • Do not use the unit in extreme humidity or heat, or where it may be affected by dust or direct sunlight. • Clean the unit with a mild detergent, and do not use solvents such as thinner. Output ................................................... 10W Speaker ................ 10cm full-range (60) x 1 Input .................................... [MIC] -45dBm [INST] -15dBm [LINE] — 15dBm Input Impedance ................ [MIC] 1 kil [INST] 50kil [LINE] 50kil Controls............................Input Volume x 1 Low Boost x 1 High Boost x 1 Consumption ................... 16W [117V], 28W [220V, 240V) Dimensions.... 132(W) x 218(H) x 165(D)mm/ 53/ie"(W) x 89/i6"(H) x 6i/2"(D) Weight ....................................2.5kg 5lb 8oz Option...........Micro Monitor AMP Holder MAH-1 • The MA-12C adopts cancelling magnet * Specifications are subject to change without notice, system, however keep floppy disks or recorded tapes away from it for safety. • In case MA-12C distorts the image on the monitor disply, locate it away from the display. ■ PANEL DESCRIPTION O Low Boost Knob This boosts the lower frequencies of the input signal. Rotating the knob clockwise deepens the effect. Usually, set it at the center position, and adjust it as you listen to the sound. 0 High Boost Knob This boosts the higher frequencies of the input signal. Rotating the knob clockwise deepens the effect. Usually, set it at the center position, and adjust...