Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
another mixer) are connected to the M-480. It consists of a stereo pair, but can be used in mono by using the Left [ L(Mono) ] side only. © Effect Send Volume These knobs control the final output level of the effect signal of each channel. The signal is extracted after the Channel Volume Knob (Postfader). * The nominal output of the Effect Send Volume is obtained when it is set to “8". (D AUX Send Volume This knob controls the final output level of the AUX signal of each channel. * The nominal output of the AUX Send Volume is obtained when it is set to "8". (§) AUX Select Switch This switch selects the point at which the signal to be sent to the AUX Send is to be extracted from the signal path. In the PRE (pre-fader) position, the signal is extracted before the Channel Volume Knob. In the POST (post-fader) position, the signal is extracted after the Channel Volume Knob. * The AUX Select Switch works simultaneously for AUX 1 and 2 in every channel. (21) This is a peak-reading meter that indicates the output level from the MASTER OUT jacks. At OdB, the standard level (+4dBm) is output from the MASTER OUT jacks. (8) Monitor/CUE (MON/CUE) Peak Meter This is a peak-reading meter that indicates the post-fader signal from the SUB OUT jacks or prefader signal from the MASTER OUT jacks. At OdB, the standard level (+4dBm) is output from the SUB OUT jacks. * When "MASTER" is selected at the Monitor Select Switch, the pre-fader signal from the MASTER OUT jacks is indicated. Normally, this peak meter indicates the signal from the SUB OUT jacks, but when you press a CUE Switch, the signal of the corresponding channel is indicated. (When a CUE Switch is pressed, only the signal of the corresponding channel will be output from the MONITOR OUT jacks and Headphone jack.) (9) CUE Indicator This indicator is green when any CUE Switch is pressed. @ Mute Indicator This indicator lights (orange) when the signal output from the MASTER OUT jacks is muted. (Jj) Power Indicator This indicator lights (red) when the mixer is switched on. © Mute On/Off Switch This switch turns the output of the MASTER OUT jacks on and off. When pressed, the output of the MASTER OUT is on, when pressed again, the output of the MASTER OUT is off. ® Master Volume Knob This knob adjusts the overall output level at the MASTER OUT jacks. * The nominal output of the Master Volume Knob is obtained when it is set to "8". 10 (14) Master Balance Knob This knob controls the volume balance (L and R) of the signal sent to the MASTER OUT jacks. At the center position, the volumes of the L and R signals are equal. © Sub Out Volume Knob This knob controls the overall output level at the SUB OUT jacks. * The nominal output of the Sub Out Volume Knob is obtained when it is set to "8". © Sub Out Balance Knob This knob controls the volume balance (L and R) of the signal sent to the SUB OUT jacks. At the center position, the volumes of the L and R signals are equal. @ Monitor Select Switch This switch selects the signal to be output from the MONITOR OUT jacks. When pressed, the pre-fader signal of the MASTER OUT jacks is selected. When pressed again, the pre-fader signal of the SUB OUT jacks is selected. * The signal to the Headphone jack can be selected in the same way. © Monitor Out Volume This knob controls the output level of the signal sent to the MONITOR OUT jacks. * The nominal output of the Monitor Out Volume is obtained when it is set to "8". © Headphone Volume Knob This knob controls the output level of the signal sent to the Headphone jack. © Headphone Jack Connect stereo headphones to this jack. The signal output to the headphone jack is the same signal sent to the MONITOR OUT jack. ® Power Switch Press this switch to turn the unit on and off. * Before switching the mixer on or off, set the Master Volume Knob to “0". * After the mixer is switched on, the muting circuits work for approx. 2 seconds and therefore no sound will be heard. 11 3. Rear Panel © CHANNEL INPUT Jacks Connect electronic musical instruments or CD player (for example) to these jacks. Be sure to use standard 1/4” phone plug. * This mixer uses an unbalanced input system. (2) RTN LEVEL (Return Level) Switch These switches controls the input level (+4 dBm or -20 dBm) of the return signal depending on the unit or device used. (3) RETURN Jacks These jacks receive the return signal from an effect device. They can also be used as auxiliary inputs. The RETURN jacks consist of stereo pairs but can be used in mono by using the L(MONO) side only. © BUS IN Jacks Signals fed into these jacks can be directly mixed with the output signals from the MASTER OUT jacks, SUB OUT jacks, MONITOR OUT jacks, AUX (SEND OUT) and EFF (SEND OUT) jacks. For instance, when two M-480s are stacked by connecting the MASTER OUT jacks, SUB OUT jacks, MONITOR OUT jacks, AUX and EFF (SEND OUT) jacks of the second mixer to the corresponding BUS IN Jacks on the first mixer, th...