Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: ARC Audio Dateigröße: 1.04 mb Dateiname: Unterrichtssprache:

. DIN Mounting Option 3. Fully Variable Band Pass Crossover 4. Sub Sonic Filter 5. Variable Sub Phase Shift. 6. Independent Front and Rear Inputs 7. 8 Volt RMS Output 8. Output Clip Indicator for Easy Gain Setting 9. 4-Layer PC Board with SMT Technology 10. Quiet Mute for Noise Free Turn-on's Advanced Design Features The IDX is designed to take full advantage the front listening positions by making it easier to make adjustment without constantly jumping in out of the car. Clearly this method does not require the sound memory typically needed to tune a system. You hear any change you make while your hand is still on the control. If it works you leave it. If it can change it back immediately. This reduces the time needed to "Get into the Ballpark" and get down to some serious fine- . Installation Information 1. The IDX needs to be installed in the signal path between your source unit and yourexternal amplifier (s). 2. Because of it's small size the IDX can be mounted almost anywhere. The chassisis designed to fit a 1/2 DIN opening. however it will work just as well under a seat orin the trunk. For easiest tuning mount it near the drivers listening position. Make surethe Crossover is kept clean, cool, and dry. Don't mount it under a cup holder or in a storage box were it will be covered with the stuff that always seems to collect in our cars. 3. . Hook up +12 volt power, ground, and remote turn-on. Make sure the ground is perfectly clean and tight. Remove all the paint and under coat before you screw itdown. Don't trust the stock ground. Make a new one. 4. Connect the front output of you head unit to the front input of the IDX. 5. You may choose to connect the rear output of the head unit to the rear input of the crossover. This is optional. Make sure the switches on top are configured correctly. 6. Connect your outputs to your amplifier (s) It is recommended that you mark yourRCA cables at both ends. This will avoid confusion and reduce the trouble shooting later on. 7. Don't fix the IDX permanently into place until you have configured all your crossovers. 8. Now the fun begins. Start tweaking. It's amazing how much a tiny adjustment toyour crossover frequency can change your system. This is a very abbreviated description of a typical install. Every install is a bit different. Take your time and read your instructions (you know you should). If you begin to feelyou're getting in over you head, Pack it back up and take it to your nearest ARCAudio dealer for professional installation. Alternate Mounting Locations Modern vehicles can be a real challenge to the creativity of The compact design and side mounted controls of the IDX open optionsfor you. Under seat installation and tuning has always been traditionalcrossover designs but the IDX can be easily tuned Likewise, many compact cars have small bins theIDX. With a little creativity the IDX can do thinkabout it, it's really more versatile the 11 IDX The Connections and Controls 1. Front Input 2. Rear Input 3. Front Output 4. Rear Output 5. Sub Output 6. Power Connector 7. Input Mode Switch 8. Front Crossover Switch 9. Rear Hi Pass X-over Switch 10. Rear Low Pass Switch 11. Sub Sonic Filter Switch 12. Sub X-Over Slope Switch 13. Front X-Over X10 Switch 14. Front X-Over Gain 15. Front Frequency Control 16. Clip and Power Lights 17. Rear High Pass X10 Switch 18. Rear High Pass Control 19. Rear X-Over Gain 20. Rear Low Pass Control 21. Rear Low Pass X10 Switch 22. Sub Sonic Filter Control 23. Sub X-Over Gain 24. Sub Frequency Control 25. Phase Shift Control 13 14 7 8 109 11 12 1 2 3 4 5 6 18 19 20 21 22 23 2415 16 17 25 XEQ IDX IDX 12 11 IDX The Connections and Controls 1. Front Input 2. Rear Input 3. Front Output 4. Rear Output 5. Sub Output 6. Power Connector 7. Input Mode Switch 8. Front Crossover Switch 9. Rear Hi Pass X-over Switch 10. Rear Low Pass Switch 11. Sub Sonic Filter Switch 12. Sub X-Over Slope Switch 13. Front X-Over X10 Switch 14. Front X-Over Gain 15. Front Frequency Control 16. Clip and Power Lights 17. Rear High Pass X10 Switch 18. Rear High Pass Control 19. Rear X-Over Gain 20. Rear Low Pass Control 21. Rear Low Pass X10 Switch 22. Sub Sonic Filter Control 23. Sub X-Over Gain 24. Sub Frequency Control 25. Phase Shift Control 13 14 7 8 109 11 12 1 2 3 4 5 6 18 19 20 21 22 23 2415 16 17 25 XEQ IDX IDX 12 1. Front Input: This is the default input. If you are using one input (2 CH.) connect your RCAs here. 2. Rear Input: Use the rear inputs for 4-channel operation. In this configuration you can have faded front and rear front your hear unit. 3. Front Output: Front output in name only. If you're using the IDX in 3-Way this will be your High Pass x-over. This is a High Pass only crossover. 4. Rear Output: The rear output can be set as High Pass, Low Pass or Band Pass. To use the Band Pass mode you will need to set both High Pass and Low Pass switches on top of the unit. With both turned on the output will switch to Band Pass. Note: For this to work t...

Herunterladen

Geben Sie zwei Ziffern: