Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Pressing Lhls key repeatedly will change the display mode as follows: The curienl position ]-} Display ol the available of the recorder section —disk space (REMAIN) ]— [ "Refer to page ’27" for more InfomiatSon about the REMAIN. Pressing this key while holding down the EXECUTE key will switch the Time Base (*) as follows. The Time Base can be set when the display shows the recorder's current position or the available disk space (REMAIN). |—y{ ABS (Absolute Time)-]-?[ BAR/BEAT7CIK ) ^ MTC (MIDI Time CodeT]—j (") Time Base: The D-90 uses time display (ABS or MTC) or Bar/Beat/Clock display to indicate the current position of the recorder section. These displays are called "Time Base." ABS (Absolute Time) shows the absolute time of the disk, and MTC (MIDI Tlmecode) shows the relative time obtained by adding an MTC offset value ro the ABS value. Bar/Beat/Clock (BAR/ BEAT/CLK) indicates a position within a piece of music and conforms to the MIDI clock and Song Position Pointers created on the Internal Tempo Map. ' Refer to papes ’98', ’118’and "120" tor more Information about MTC and the Internal Tempo Map. 19. Execute/Yes key [EXECUTE/YES] Press this key to execute the operation when you try to edit data on the hard disk using the edit /unctions such as Paste and Erase, when you put the D-90 into SETUP mode, or when you set the parameters In the SETUP menu. Pressing the DISP SEL key while holding down the [EXECUTE/YES] key allows you to select the Time Base. (Refer to the explanation about the DISP SEL key.) I ’ Retar to page ’77* lor mom information about using this key tor the Paste or Erase operation. I • Refer to page ’114" tor mote Information about using this key in SETUP mode. 20. Exit key/No key [EXFT/NO] Contrary to the EXECUTE/YES key, this key is used to stop the operation. I " Rater to page 77" tor more information about using this key for the Paste or Erase operation. I ’ Refer to page ’ 114’ for mom Information about using this key In SETUP mode. 21. Recall key [RECALL] Press this key to recall the stored time vaiut? (or Bar/Beat/Clock value). Pressing this key, then one of the following keys will display the data stored at the key you pressed, and you will be able to edit the data. RECALL key -> CLIPBOARO IN key The Clipboard In point Is recalled am the unit enters etft mode. RECALL key •» CUPBOARD OUT key The Clipboard Out pelm Is recalled ard the unH enters edit mode. RECALL key -> AUTO PUNCH IN key The Auto Punch In point ts recalled and the unit enters edit mode. RECALL key ■> AUTO PUNCH OUT key The Auto PvnOi Out point is recalled tod the unit enters etSt mode. RECALL key •» AUTO RTN START key The Auto Return Start point Is recaSed and the unit enters edit mode. RECALL key -> AUTO RTN END key The Auto Return End point Is recalled and the unit enters edil moda. RECALL key •> LOCATE key The locals key data is mailed end the unit oners «Sí mode. To exit edit mode, press the EXIT/NO key, DISP SEL key, or STOP button. 18 D-90 Owner's Manual (Names and Functions) ' Refer to page '77* lor more Information about the clipboard. ‘ Refer to page '67' for more intormation about Auto Punch In/Out recording. ’Refer to page ’61" tor more Information about Auto Return. 22. Store key [STORE] This key is used to store a time value (or Bar/Beat/Qock value) to one oftbe memory keys. Pressing this key, then one of the following keys will cause the data shown on the display to be stored to the corresponding memory key you pressed. Pressing the STORE key while holding down the HOLD/> key will change a Program. STORE key -> CLIPBOARD IN key Data is stored as a C/ipboard In point. The stored data can be used as a locator. STORE key -> CLIPBOARD OUT key Data is stored as a Clipboard Out point. The stored data can be used as a locator. STORE key -> AUTO PUNCH IN key Data is stored as an Auto Punch In point the stored data can be used as a locator. STORE key ■> AUTO PUNCH OUT key Data is stored as an Auto Punch Out point The stored data can be used as a locator. STORE key -> AUTO RTN START key Data Is stored as an Aulo Return Start point. The stoted data can be used as a locator. STORE key -> AUTO RTN END key Data is stored as an Aulo Return Endpoint. The stored data can be used as a locator. STORE key -> LOCATE key Data is stored as a LOCATE key data. After pressing this key, if you change your mind and wish to cancel the store operation, press the EXIT/NO key, DISP SEL key, or STOP button. * Refer to page *77* for more information about the cEpboard. ’Refer to page '33'and '4$“ for more Information about Program Change function. * Refer to page '61'for more information about the Locate function. * Refer to page ’67'for more information about Auto Punch In/Out recording. * Refer to page '61'for more Information about Auto Return. 23. Hold/Digit Move key [HOLDA>] Pressing this key while the recorder transport Is operating will hold the time value (or Bar/Beat/Clock...