Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Clear the entire ponce in stop mode or program twice while playing. Tips • The program you created remains in the CD player's memory even after it has been played. Press ato play the same program again. • If “--.--” appears instead of the total playing time while programming, this means: – you have programmed a track numbered over 20, or – the total playing time has exceeded 100 minutes. Playing CDs without interruption –– Non-Stop Play You can play CDs without pausing between tracks. 1 23 1 Press FUNCTION repeatedly until “CD” appears in the display. 2 Press NON-STOP so the indicator on this button lights up. 3 Press a. To cancel Non-Stop Play Press NON-STOP so the indicator on this button goes off. The Tape Deck The Tape Deck Recording on a tape manually You can record from CDs, tapes, or the radio as you like. For example, you can record just the songs you want or begin recording from the middle of the tape. The recording level is adjusted automatically. 2 DOLBY »p 4 4 NR 5 13 1 Insert a blank tape into deck B. 2 Press FUNCTION repeatedly until the source you want to record (e.g., CD) appears in the display. 3 Press rREC. Deck B stands by for recording, and the indicator on the abutton (for the front side) lights up green. 4 Press DIRECTION repeatedly to select Ato record on one side or §(or RELAY) to record on both sides. 5 Press Pon deck B. Recording starts. 6 Start playing the source to be recorded. To Press Stop recording pon deck B Pause recording Pon deck B Tips • If you want to record on the reverse side, press . so the indicator on the » button (for the reverse side) lights up green. • When you want to reduce the hiss noise in low- level high-frequency signals, press DOLBY NR before step 5 so “DOLBY NR B” appears in the display. Recording CDs by specifying the track order — Program Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. 12 21113 3 pp 915 EDIT 6 4,7 CHECK 1 Place CDs and close the front cover. 2 Insert a blank tape into deck B. 3 Press FUNCTION repeatedly until “CD” appears in the display. 4 Press PLAY MODE repeatedly until “PROGRAM” appears in the display. 5 Press DISC SKIP to select a CD. 6 Turn the jog dial until the desired track appears in the display. Disc number Track number DISC PROGRAM DOLBY NR OFF Total playing time (including selected track) 7 Press PLAY MODE once. The track is programmed. “STEP” and the programmed playing order appear, followed by the total playing time. The last programmed track DISC PROGRAM DOLBY NR OFF Previously selected track 8 Repeat steps 5 through 7 to program additional tracks to be recorded on side A. Skip step 5 to select tracks from the same disc. 9 Press P to insert a pause at the end of side A. “P” appears in the display and the total playing time resets to “0.00” in the display. continued Recording CDs by specifying the track order (continued) 10Repeat steps 5 through 7 to program the tracks to be recorded on side B. Skip step 5 to select tracks from the same disc. 11Press CD SYNC. Deck B stands by for recording, the CD player stands by for playback, and the indicator on the abutton (for the front side) lights up green. 12Press DIRECTION repeatedly to select Ato record on one side, or §(or RELAY) to record on both sides. 13Press Pon deck B. Recording starts. To stop recording Press pon deck B or on the CD player. To check the order Press CHECK on the remote repeatedly. After the last track, “CHECK END” appears. To cancel Program Edit Press PLAY MODE repeatedly until “PROGRAM” or “SHUFFLE” disappears from the display. Selecting the tape length automatically — Tape Select Edit You can check the most suitable tape length for recording a CD. Note that you cannot use Tape Select Edit for discs containing more than 20 tracks. /After inserting a CD, press EDIT once so “EDIT” flashes. The required tape length for the CD in the playing position appears, followed by the total playing time for sides A and B. Note You cannot use this function when Program Play mode has been set. After clearing the entire program (see “To clear the entire program” on page 25), follow the above procedure. DJ Mix DJ Mix Looping part of a CD Flashing part of a CD — Loop — Flash With the loop function, you can repeat part of With the flash function, you can “flash” the a CD during playback. This lets you create CD sound during playback. This lets you original recordings. create original recordings. LOOP Jog dial /Press and hold LOOP during playback at the point you want to start the Loop function, and release to resume normal playback. To adjust the loop length Turn the jog dial while holding LOOP (or press MUSIC MENU B/bwhile holding LOOP on the remote) to select different loop lengths. LOOP FLASH Jog dial /Press and hold FLASH during playback at the point you want to start the Flash function, and release to resume normal playback. To adjust the flash...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - LBT-XB8AV (689.21 kb)