Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Atomic, modell 50-112

Hersteller: Atomic
Dateigröße: 649.75 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

If your modeler has a ON/OFF switch, switch it ON now. .. Use the power cable included with the docking template to connect between your modeler’s power input and the DS-1s power output. THERE IS NO NEED FOR AN EXTERNAL POWER SUPPLY. The DS-1 automatically compensates for your modeler’s voltage and polarity. Check if everything is connected correctly and then let the „Docking Station“ click into place. If this sounds complicated, don’t worry, it isn’t. Just try it, it’s easier than you think. Now turn the Master-Volume-Control on the rear side of the Atomic to the left (Volume off) and switch the red Power Switch on, after of course connecting the amplifier to the mains. Your Modeler will also switch on and the red power switch will light up, err red? Yeah you guessed it. Even the tubes will start to glimmer now. A tube amp needs time to warm up, the tubes need about 30 seconds to get up to their working temperature. Now turn on the blue Stand-By switch, which will light up green, no sorry only joking, it will light up blue. Now connect your guitar to the Input Jack of your Atomic Amp. Turn the Master-Volume-Control on the rear side of the amp and the Output-Level-Control of your Modeler to the required volume and it’s time to start rocking. If you connected all your cables like we suggested and your Modeler is turned on, you should be surrounded by amazing tube analogue mixed with digital Modeler sounds, making crisp and warm guitar amp sounds. The right Output Jack of the DS-1 connects the Modeler directly to the Send-R-Jack of the Atomic Reactor-Effect-Loop on the rear side. The signal is mono until a cable is put into the Send-R-Jack. If you use a multi-effect device or just plain old stomp machines, they can be connected using the normal Send and Return Jacks of the Atomic Amp. Using the red push-button you can switch the Effect-Loop from mono to stereo. Check your Modeler manual for information about controlling the output level. For Rich Kids: If you want a really professional stereo solution, buy a second Atomic Reactor amp. Connect the Send-R-Output from the first Atomic Amp (the one with the Modeler!) with the Return-Jack on the rear of the second Atomic Amp. For even Richer Kids: Wanna use more than one Modeler? No problem, just order a second, third, fourth or fifth DS-1 and the Template Kit for your Modelers. Set up like we described earlier and during a gig, you can snap one out, snap a new one in, without turning the Atomic Amp off. The new Modeler is ready for use immediately. Special instructions for owners of Floor-Amp-Modelers and other Modelers not mentioned above Do not despair, if you own one of these devices and cannot use the DS-1 Docking Station. We will show you how it is done. Installing a Blank Template into the DS-1 .. First locate the 8 screws attaching the template frame to the top of the DS-1. There are 4 screws that come in groups of 2 on each side. Remove these screws (and don’t lose them!) using a properly sized Phillips-head screwdriver. . .. Remove the template frame of the DS- 1 Still got the screws? . .. Replace the template frame with a blank template (Atomic Part # ATBLANK – purchased separately). Still got the screws? . .. Replace the 8 screws. (Whew!) You can now load the DS-1 into the Reactor as usual *. The Reactor is now ready to be used with a Pro-rack or foot controller style modeler * NOTE! When bypassing the DS-1, the “RETURN” input on the rear jack panel of the Reactor 50 112/212 should be used as the Reactor’s main input, (see pages 11-14). Inserting a jack into the RETURN puts the Reactor in “Direct Mode” and automatically cancels out the open audio cables from the DS-1. Return the DS-1 into it’s place in the Atomic Amp with a snap – and that’s it! Turn the Master-Volume-Control on the rear of the Atomic Amp down. Connect the amp to your favourite mains socket. Turn on the Power Switch (red), wait the obligatory 30 seconds until the tubes are warm. Now turn the Stand-By switch on (blue) and adjust the gain level on the Master-Volume the Atomic Amp and your Modeler and you will hear those fantastic warm, crisp Guitar/Amp sounds blow your tootsies off! For Rich Kids: If you want a really professional stereo solution, buy a second Atomic Reactor amp. Connect the Send-R-Output from the first Atomic Amp (the one with the Modeler!) with the Return-Jack on the rear of the second Atomic Amp. Desktop Modeler in Stereo RETURNSEND - L EFFECTS LOOPSEND - RMODEL REACTOR 112Atomic Amplifiers LLC. Orange CT. FUSE0101010101!CAUTION! RETURNSEND - L EFFECTS LOOPSEND - RMODEL REACTOR 112Atomic Amplifiers LLC. Orange CT. FUSE0101010101!CAUTION! * PLEASE NOTE! If you wish to use a pair of Reactors in MONO, simply use the SEND – L output instead of SEND – R. .. After obtaining the proper template load your modeler into the DS-1 that comes provided with your Reactor 50 112/212. .. Load the DS-1 into the docking bay located in the top of Reactor #1, making sure that the dock loc...