Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
>> Click here to see an animation clip Power button [ ] Use this button for turning the monitor on and off. Power indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Rear The configuration at the back of the monitor may vary from product to product. POWER S/W / POWER POWER S/W : Switches the monitor On/Off. POWER : Connect the power cord for your monitor to the POWER on the back of the monitor. DVI IN(HDCP) / RGB IN DVI IN(HDCP) : Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor. RGB IN : Connect the RGB IN terminal at the back of your monitor to your computer. AUDIO POWER • Connect the speaker power line connected to the speaker to the AUDIO POWER terminal of the monitor Kensington Lock • The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Stand Stopper • Remove the fixing pin on the stand to lift the monitor up and down. See Connecting Cables for further information regarding cable connections. Connecting Cables Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. Using the RGB (Analog) connector on the video card. - Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. [ RGB IN ] Using the DVI (Digital) connector on the video card. - Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor. [ DVI IN(HDCP) ] Connected to a Macintosh. Connect the monitor to the Macintosh computer using the RGB connection cable. If the monitor and the computer are connected, you can turn them on and use them. Connecting a Speaker ( When connecting a speaker, be careful that the grooves of the monitor and the speaker . )are aligned with each other. Adjust the aligned positions until you hear a ‘click’. If a speaker is connected correctly, you can hear a ‘click’.If a speaker is connected without you hearing a ‘click’, the holding part may become damaged. If you need to separate, please pull ( ) a little and push to the right. MIC / SPK Connect the red cable of the cables provided when the speaker was purchased to the audio output terminal at the back of the computer. Connect the other end of the cable to the red terminal at the back of the speaker. Connect the light green cable of the cables provided when purchasing the speaker to the audio output terminal at the back of the computer. Connect the other end of the cable to the light green terminal at the back of the speaker. / Connect a headphone to the black terminal at the right of the speaker. Connect a microphone to the red terminal at the right of the speaker. By turning part ( + , - ) in the direction shown in the figure below, the speaker turns on and the volume increases. Connect the power line connected to the speaker to the black terminal of the monitor. This speaker is not connected to an external power source. It is connected to a monitor for the required power. Using the Stand Sliding stand Stand Stopper Swivel stand Using ( ),You can swivel the monitor left and right at an angle of 350° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed. Tilt angle Using ( ), You can adjust the tilt anlgle within a range of 3° forward to 25° backward for the most comfortable viewing angle. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant Mounting interface pad. Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. • Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor. • For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. • Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. • Samsung is not liable for product d...