Stimmen - 6, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. If the cabinet becomes dirty, wipe it with a soft, dry cloth. • If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. • Do not allow any detergent to come into direct contact with the surface of the LCD Display. If water droplets get inside the unit, operating problems may result. • Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. Accessories Accessories Supplied Check that you have the Accessories and items shown Operating Remote Control Batteries for the Warranty Instruction book Transmitter Remote Control EUR646535 Transmitter (AA Battery . 2) DISPLAY INPUT SURROUND VOL N R PICTURE SOUND SET UP ASPECT PICTURE POS. /SIZE OFF TIMERPC MULTI PIP SWAP SELECT ZOOM MOVE Ferrite core Ferrite core (Small size) . 2 (Large size) . 2 AC cordFixing bands . 2 Remote Control Batteries Requires two AA batteries. 2. Install the batteries as shown in the battery compartment. (Polarity + or – must match the markings in the compartment.) 1. Turn the transmitter face down. Press and slide off the battery cover. 3. Replace the cover and slide in reverse until the lock snaps. Two “AA” size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the LCD Display. 9 Connections PC IN SERIAL AUDIO SLOT1 SLOT2 AUDIO VIDEO IN VIDEO OUT IN R L S VIDEO IN AV AUDIO VIDEO IN IN R L S VIDEO IN SLOT 2 AV R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT 1 AUDIO PC IN SERIAL VIDEO OUT 1 2 COMPONENT/RGB IN R AUDIO L VD HD PR/CR/R PB/CB/B Y/G 1 2 1 SPEAKERS 2 Terminals (R) SPEAKERS Terminals (L) – Cable fi xing bands Secure any excess cables with bands as required. When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Speakers (Optional accessories) Pass the attached cable fi xing band through the clip as shown in the fi gure. To secure cables connected to Terminals, wrap the cable fi xing band around them then pass the pointed end through the locking block, as shown in the fi gure. While ensuring there is suffi cient slack in cables to minimize stress (especially in the power cord), fi rmly bind all cables with the supplied fi xing band. From SERIAL Terminal on Computer (see page 11) From EXTERNAL monitor terminal on Computer (see page 10) AC cord connection (see page 13) COMPONENT/RGB IN and Audio IN Terminals (see page 12) AV Terminals (see page 12) To tighten: To loosen: Pull Pull Push the catch 3. Slide up the clamper and fi x the AC cord plug securely. 2. Insert the AC cord and close the clamper securely. 1. Open the clamper. Clamper AC cord Note: The power plug in the illustration may not be the type fi tted to your set. When loosen the clamper: Note: At factory shipment, Terminal boards are installed in SLOT 1 and SLOT 2. – AC cord fi xing 4. Insert the point of the fi xed clamper into the small hole on the lower r i g h t o f the back cover as necessary. Connections PC Input Terminals connection AUDIO PC IN TH-32LHD7 COMPUTER Conversion adapter (if necessary) D-sub 15pRGB PC cable Ferrite core (Small size) (supplied) Less than 3” 15/16 (10 cm) Stereo plugAudio Less than 3” 15/16 (10 cm) Connect a cable which matches the audio output terminal on the computer. 1 2 3 Installing the ferrite core (Small size) Pull back the tabs (in two places) Open Press the cable through and close Notes: • Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display resolution is a maximum of 1,024 . 768 dots when the aspect mode is set to “NORMAL”, and 1,366 . 768 dots when the aspect mode is set to “FULL”. If ...