Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Campbell Hausfeld, modell PW2570

Hersteller: Campbell Hausfeld
Dateigröße: 4.23 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Follow manufacturer’s label directions for mixing correct concentrations of soap/detergents The soap detergent to water ratio through the pump is approximately 12% (1 to 8) 2 . Insert the filter end of the clear plastic detergent tube into the detergent container 3. Install 65. (Black) Low Pressure Detergent Tip in the quick connect fitting on the end of the lance neVer replace quick connect tip when gun is triggered. Always engage trigger lock on gun before removing or installing quick connect tips. GeNerAL CLeANING TIPS 1 . Apply the detergent so that it thoroughly covers the cleaning surface Apply the detergent from bottom to top to prevent the detergent from sliding down and streaking Wait a couple of minutes for the detergent to break down the dirt and grime Use a brush to lightly scrub heavily soiled areas Never allow the detergent to dry on the cleaning surface 2. Replace black 65. quick connect tip with the yellow 15. tip and complete final rinse neVer replace quick connect tip when gun is triggered. Always engage trigger lock on gun before removing or installing quick connect tips. 3 . NOTE: After using detergents, flush the suction system by placing the detergent suction tube into a bucket of clean water and running unit with black 65. tip flushing clean water from tank through the pump 8 Pressure Washer Operation 5. CLeANING POWer The easiest way to regulate the cleaning power of your pressure washer is by changing the distance from the surface you are cleaning Begin spraying while standing several feet from the surface Slowly move closer to the object you are cleaning until you find the most effective cleaning technique 6. FINAL rINSe The final rinse should start at the bottom and work upward Make sure that you thoroughly rinse the surface and that you remove all detergent 7. PreSSure reLIeF PrOCeDure To reduce the risk of bodily injury or property damage, always follow this procedure whenever spraying is stopped, when work is completed, and before checking or repairing any part of the system 1 Engage the trigger safety latch 2 Turn the unit off 3 Shut off the water supply 4 Disengage the trigger safety latch and trigger the gun to relieve pressure 5 Re-engage the trigger safety latch 6 When checking or repairing unit, remove the ignition cable from the spark plug 7 Before overnight storage, long term storage, or transporting unit, disconnect the water supply and turn off the fuel supply valve 8. SHuTDOWN 1 Be sure all detergent is flushed from system 2 Turn the engine OFF 3 Turn the water supply OFF 4 . After the engine and water supply are turned off, trigger the gun to depressurize the system neVer turn the water supply off before turning the engine/motor off. serious damage could occur to the pump and/or engine/motor. neVer disconnect the high pressure discharge hose from the machine while the system is pressurized. To depressurize, turn engine/motor off, turn water supply off and squeeze gun trigger 2-3 times. 5 . After each use, wipe all surfaces of the pressure washer with a clean, damp cloth • Do not store the pressure washer outdoors. • Do not store the pressure washer where it might freeze unless it has been properly winterized 9. STOrAGe LONG TerM STOrAGe INSTruCTIONS (MOre THAN 30 DAYS IN STOrAGe) 1 . Remove fuel from the tank and run the pressure washer in a normal operating mode until the engine stops from a lack of fuel Normal operating mode means actually spraying water from the gun while the engine is running Alternate method – Add fuel stabilizer to gas in the tank and run in normal operating mode for at least five minutes 2 . Stop the engine, turn off the water supply, and trigger the gun to release pressure in the high-pressure hose 3 . Disconnect the water supply and high pressure hose from the pump 4 Allow the engine to cool 5 Disconnect the spark plug wire and remove the spark plug 6 Pour 1/2 oz of engine oil into the spark plug hole never pull the starter rope on the engine when the spark plug is removed unless the spark plug hole is covered. Fuel vapor from the hole can ignite by a spark. 7 . Place a rag over the spark plug hole and slowly pull the starter rope several times to distribute the oil WINTerIzING INSTruCTIONS 1 . Follow and complete the Long Term Storage Instructions above 2 Disconnect the spark plug wire 3 Disconnect the high pressure hose from the pump 4 . Insert a 12 inch to 14 inch piece of garden hose into the pump inlet 5 Place a funnel in the other end of the garden hose read the manufacturer’s instructions for safe handling and disposal of rV antifreeze. 6 Pour approximately 6 oz of RV antifreeze into the funnel 7 . Pull the starter rope several times until the RV antifreeze comes out of the pump outlet 8 . Disconnect the high pressure hose from the gun and drain the hose Hold the gun and lance in a vertical position and squeeze the trigger to drain the water out TIPS FOr exTeNDING THe LIFe OF YOur PreSSure WASHer 1 Never operate the u...