Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Your pressure washer is not meant to pump hot water Never connect your pressure washer to a hot water supply as it will significantly reduce the life of the pump 3 . Running the unit for more than one minute without spraying water causes heat to build up in the pump Running the unit without spraying water can damage pump components 9 Pressure Washer Maintenance Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer Refer to the schedule for recommended maintenance If you operate the pressure washer in dusty conditions, perform maintenance checks more often eNGINe OIL CHANGING INSTruCTIONS Drain the engine oil when th engine is warm Warm oil drains quickly and completely 1 . Turn the fuel valve to the OFF position to reduce the possibility of fuel leakage 2 . Place a suitable container next to the engine to catch the used oil 3 Remove the oil filler cap/dipstick and drain the oil into the container by tipping the engine toward the oil filler neck Please dispose of used motor oil in a manner that is compatible with the envirionment We suggest you take used oil in a sealed container to your local recycling center or service station for reclamation Do not throw into the trash, oust it on the ground, or pour it down a drain 4 . With the engine in a level postion, fill to the upper limit mark on the dipstick with the recommended oil running the engine with a low oil level can cause engine damage. 5 Reinstall the oil filler cap/dipstick securely MAINTeNANCe SCHeDuLe Maintenance Schedule Action Needed Daily • Check water inlet screen and filter • Check engine oil levels. Fill as necessary • Check gasoline level. Fill as necessary After first 5 hours of • Change engine break-in operation oil Use SAE30 or 10W-30 detergent oil Every 25 hours of • Change oil if operating under operation heavy load or high ambient temperature • Clean or replace paper air cleaner cartridge Tap gently to remove dirt Every 50 hours of • Change oil. operation • Replace spark plug. Each 100 hours of • Replace paper air cleaner operation or every 3 cartridge months • Change engine oil. Oil filler neck Oil filler cap/ dipstick Upper limit Figure 12 – Oil Drain Location PuMP OIL CHANGING INSTruCTIONS Changing or refilling the oil in the pump requires removal of the pump from the engine and should not be required unless oil has leaked out due to worn or damaged oil seals in the pump If oil has leaked out of the pump, bring the pressure washer to a certified Campbell Hausfeld service center for repair TeCHNICAL AND CONSuMer INFOrMATION vertical Oriented Pressure Washers engine Oil Type SAE 10W-30 SAE 30W (Above 60° F) engine Oil Capacity Honda Engines 18 5 fl oz engine Fuel Capacity Honda Engines 0 29 gal Pump Oil Type Wobble Pumps SAE30W non-detergent oil Pump Oil Capacity Vertical Wobble Pumps 2 7 fl oz Pump Detergent Suction Water to detergent ratio 8 to 1 (12% detergent) Water Supply requirements Minimum inlet pressure 20 psi Maximum inlet pressure 100 psi Maximum inlet temperature 100° F Minimum inlet flow rate 5 gpm Inlet garden hose size 5/8 inch I D Maximum inlet garden hose length 50 feet 10 Pressure Washer Service record Date Maintenance performed replacement components required 11 Pressure Washer replacement Parts List ––– Pump PM343501SJ For replacement parts or technical assistance, Call 1-800-330-0712 Please provide following information: Address any correspondence to: -Model number Campbell Hausfeld -Serial number (if any) Attn: Customer Service -Part description and number as shown in parts list 100 Production Drive Harrison, OH 45030 U S A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1920 21 22 24 25 26 27 28 29 30 23 ref. No. Description Part Number Qty. ref. No. Description Part Number Qty. 1 2 Pump Housing Oil Seal Ring l l 0 0 24 25 Piston Guide Body Oil Seal Ring PM270306SV 1 3 3 Bearing l 0 26 Oil Seal Spacer 3 4 Wobble Plate l 0 27 Seal Ring Seat 3 5 Thrust Shoe n 1 28 Water Seal 3 6 Ball Bearing n 1 29 Brass Swivel Assembly PM041360SJ 1 7 Bearing Disk n 1 30 Engine Mounting Bolt MJ102302AV 1 8 Suction Valve Assembly s 3 replacement Kits 9 10 11 12 13 14 15 High Pressure Valve Assembly Thermal Relief Valve Piston Piston Spring O-Ring -67 x 2 5 O-Ring -17 x 3 x 2 62 O-Ring -11 1 x 1 78 s PM345016SJ t t u u u 1 1 3 3 1 1 3 l n s t u Housing Assembly Ball Bearing Assembly Valve Assembly Piston Kit O-ring Kit Detergent Injector Kit Unloader Assembly Kit Seal Kit — PM270300SV PM270301SV PM270302SV PM270303SV PM270210SV PM270304SV PM270307SV 16 Hose Barb 1 17 Unloader Valve Assembly 1 18 Spring 1 19 Chemical Injector Assembly 1 20 Compensation Valve Assembly 1 21 22 Pin Head, Brass PM270305SV 2 1 Oil capacity: 2 7 fl oz OIl type: SAE 30W (non-detergent) 23 Head Bolt PM345213SV 1 12 s sss lns lllln Torque Specifications (in lbs) ref. No. Description Torque 10 Thermal relief valve 110 23 Head Bolt 110 16 Hose Barb Torque ...
Dieses Handbuch ist für folgende Modelle:Hochdruckreiniger - PW2570 (4.23 mb)