Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F). 6. Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 4). 7. Turn ON water, point gun in a safe direction and squeeze trigger to purge pump system of air and impurities. Checklist Before Starting Engine Review the unit’s assembly to confirm you have performed all of the following: 1. Make sure handle is secure. 2. Check for properly tightened hose connections. 3. Check to make sure there are no kinks, cuts, or damage to high pressure hose. 4. Check that oil has been added to proper level in engine crankcase. 5. Add proper fuel to fuel tank. 6. Provide a proper water supply (not to exceed 100°F). 7. Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer. CAUTION • Refer to engine operaor’s manual for oil and fuel fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. Section 3: Assembly Connect high pressure hose here Figure 3 — Connect High Pressure Hose to Spray Gun Inspect inlet screen. DO NOT use if damaged or missing; clean if dirty. Figure 4 — Connect Garden Hose to Water Inlet CAUTION • Damage to equipment resulting from failure to follow this instruction will void warranty. There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other conveniencetype water shut-off valve. • Always wear safety goggles when using this equipment or in vicinity of where equipment is in use. • Before starting the pressure washer, be sure you are wearing adequate safety goggles. High pressure spray can cause paint chips or other particles to become airborne. WARNING 9 HOW TO USE PRESSURE WASHER If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-743-4115. Pressure Washer Location Pressure Washer Clearance Place pressure washer in a well ventilated area, which will allow for removal of deadly exhaust gas. DO NOT place pressure washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes or other openings that can allow exhaust gas to collect in a confined area (Figure 5). Prevailing winds and air currents should be taken into consideration when positioning pressure washer. How to Start Engine The best way to start your pressure washer for the first time is to follow these instructions step–by–step.This starting information also applies if have let the pressure washer sit idle for at least a day. 1. Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 5.0 gallons per minute and no less than 20 PSI at pressure washer end of garden hose. 2. Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations. 3. Make sure unit is in level position. 4. Connect garden hose to water inlet on pressure washer pump. 5. Turn ON water, point gun in a safe direction and squeeze trigger to purge pump system of air and impurities. 6. Attach nozzle extension to spray gun (Figure 6). Tighten by hand. 7. Select desired quick connect spray tip and insert it into end of nozzle extension (see “How To Use Spray Tips”). 8. Engage trigger lock on spray gun trigger (Figure 7). Figure 5 — Pressure Washer Clearance Exhaust Port Typical Pressure Washer Shown • Operate pressure washer ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings. • DO NOT operate pressure washer inside any building or enclosure, even if doors or windows are open. Running engine gives off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. WARNING • Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead. Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire. WARNING Trigger Lock Figure 7 — Spray Gun with Trigger Lock Engaged Figure 6 — Connect Nozzle Extension to Spray Gun CAUTION • Damage to equipment resulting from failure to follow this instruction will void warranty. DO NOT run the pump without the water supply connected and turned on. 4 Operation Section 10 9. When starting engine, position yourself as recommended in Figure 8 and start engine according to instructions given in engine operator’s manual.Also see operating instructions tag located on the pressure washer. NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer. How to Stop Pressure Washer 1. Let engine idle...