Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: North Star Dateigröße: 781.91 kb Dateiname: 157301.pdf Unterrichtssprache:

Always use two hands for safe operation. 10.) Trigger. Actuate to allow pressurized water to flow out of spray gun. *Note: 157301 shown, location of components on other models vary slightly. Pump Component Identification 11 157300 157301 & 157302 FIG02309 Operation Instructions Water Supply 1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance. 2.) An insufficient water supply will damage your pump. Make sure the water supply is steady and is 20% over the rated flow of your pump. Use a stopwatch to time how long it takes to fill a 5 gallon bucket with your garden hose. The bucket must fill faster than the times listed in the table below. Model Time to fill 5 gallon bucket 157300 150 seconds 157301 160 seconds 157302 96 seconds 3.) The water supply garden hose must have an inside diameter of at least 5/8”. If the hose is more than 100 ft. long, the diameter must be at least 3/4”. 4.) Never use a reservoir tank as a water source. Drawing water out of a tank may cause pump cavitation and damage to your pump. This pressure washer is designed for a pressurized water source such as a city water faucet. However, the water source pressure must not exceed 115 psi (8 bar). 5.) Always use a flexible rubber hose for your water supply. Do not use rigid piping. Operation Instructions Operation Instructions START-UP INSTRUCTIONS 1. Attach garden hose. 2. Attach pressure hose. 3. Attach gun and lance. 4. Turn water supply ON. 5. Squeeze trigger to purge air from pump. 6. Insert nozzle. 7. Plug in power cord 8. Reset the GFCI button on the cord 9. Start motor. SHUT-DOWN INSTRUCTIONS 1. Turn motor OFF. 2. Unplug the power cord. 3. Turn water supply OFF. 4. Squeeze trigger to relieve system pressure. 5. Remove garden hose. 6. Remove pressure hose. Skin puncture hazard. High pressure fluid can inject under skin resulting in serious injury including amputation. Do not direct spray at people or animals. -If skin injection happens, seek IMMEDIATE surgical treatment. -Do not check for leaks with hand. Instead, use a piece of cardboard to check for leaks. -Do not use unit if exterior hose damage is evident. Make sure all fittings are tight before starting. Relieve system pressure before servicing. -Know how to stop engine and bleed pressures quickly. Be thoroughly familiar with the controls. -Make sure accessories meet the unit's temperature and pressure limits. -Stop engine and bleed pressures before leaving unit unattended. WARNING Operation Instructions 13 Spray Gun Safety Lock When not spraying, use the spray gun safety lock to prevent accidental high pressure discharge. Attaching the Lance Tighten spin-on coupler hand tight. Note: The o-rings make the seal so there is no need to tighten with a wrench. spray gun spray gun safety lock lance spin-on coupler Operation Instructions 14 Flying objects. Make sure nozzle is secure before squeezing trigger. If nozzle is not secure it will become a projectile. Serious injury can occur. WARNING Installing Nozzles To install a nozzle pull back the collar and push the nozzle into the coupler. Once the connection is made, pull on the nozzle to make sure it is secure. Attach Quick Connect Couplers -To install the hose onto the pump, pull back the collar and push the hose into the coupler on the pump. -To install the hose onto the spray gun, pull back the collar on the spray gun and push the hose into the coupler on the spray gun. Once the connections are made, pull on the hose to make sure it is secure. CORRECT INCORRECT nozzle collar coupler lance collar completely pushed out. collar NOT completely pushed out. pump hose spray gun Operation Instructions 15 Applying Chemicals 1.) Install the black nozzle when applying chemicals onto the cleaning surface. 2.) Start the pressure washer according to the start-up instructions. 3.) Submerge the chemical hose in cleaning solution. 4.) Squeeze the spray gun trigger. The chemical injector will draw the chemical into the water stream. 5.) Apply chemicals evenly onto the cleaning surface. Allow the chemicals to react with the dirt, then clean at high pressure with high pressure (green or yellow) nozzle. 6.) Never use more chemical than is necessary to clean the surface. 7.) To clean the chemical injector, draw water through the strainer until all the chemical is purged from the system. Risk of exposure to dangerous chemicals. Serious injury or death can result if chemical manufacturer instructions are not followed. -Wear protective gloves when handling and cleaning with chemicals. -Understand all safety hazards and first aid for all chemicals being used. -When cleaning filters, check if chemicals have been used and take any precautions that are recommended by the chemical manufacturer. -Different chemicals may interact dangerously with each other, always follow chemical manufacturer directions before switching chemicals. -Calculate the correct amount of chemical to mix, dispose of excess chemical per the manuf...

Herunterladen

Geben Sie zwei Ziffern: