Insert attachment into hole and turn slowly until tabs slip into slots in hole. Push in until attachment locks in place. Then insert the beater marked L, with the rounded bottom. If difficult to insert, turn beater one quarter turn and try again. Right Left How To Use Your Stand Mixer Head slightly and press Mixer Release button to release. Lower into bowl. When lowered, the Mixer Head automatically locks into place. 7. Plug cord into electrical outlet. Select desired speed. Prepare recipe accor

A short cord is provided to reduce the hazard of becoming entangled or tripping over a longer cord. An extension cord may be used if the electrical rating is equal to or greater than the rating of the mixer. Use an extension cord rated 10 amperes or greater. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over. Know Your Stand Mixer Parts and Features 1. Mixer Head 2. Beater Eject Button 3

8 Canada : 1-800-267-2826 Consulter hamiltonbeach.ca pour des recettes delicieuses et pour enregistrer votre produit! Espanol ...................................................................................... 14 Mexico: 01 800 71 16 100 Visite hamiltonbeach.com para recetas deliciosas y para registro de su producto en linea. Le invitamos a leer cuidadosamente este instructivo antes de usar su aparato. READ BEFORE USE LIRE AVANT L’UTILISATION LEA ANTES DE USAR 840163800 840163800 ENv03.qxd 4/

There is no warranty with respect to the following, which may be supplied with this product, including without limitation: glass parts, glass containers, cutter/strainers, blades, seals, gaskets, clutches, motor brushes, and/or agitators, etc. This warranty extends only to the original consumer purchaser and does not cover a defect resulting from abuse, misuse, neglect including failure to clean product regularly in accordance with manufacturer’s instructions, use for commercial purposes, or any

See Mixer Operation for recommended loading sequence. If forage is piled above reel, they may be wedged against the side when started up. KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 TROUBLE SHOOTING PROBLEM: MOTOR RUNS, BUT REEL AND AUGERS DO NOT TURN CAUSE SOLUTION SHEAR BOLT ON PTO DRIVELINE HAS SHEARED BELTS ARE SLIPPING BROKEN CHAIN Replace with Same Grade and size shear bolt. Do not us any bolt other than a Gr 5 see P

Second adjust by loosening top load cell mount in a no load condition, adjust load cell to a vertical position and tighten fasteners. Remove pin check assembly, test scale, if scale operates properly clean or repair pin check assembly. Also see “INSPECTIONS AND ADJUSTMENTS SECTION” lubricate check arm (should rotate on sockets without great effort). Also see “INSPECTIONS AND ADJUSTMENTS SECTION” PROBLEM: SCALE WEIGHS VERY HEAVY OR VERY LIGHT, WEIGH BAR ONLY CAUSE SOLUTION IMPROPER CALIBRATION DA

DANGER: NEVER ATTEMPT TO RELEASE JAMMED MATERIALS OR CLEAN MATERIALS from any area of the mixer or discharge chute without stopping mixer and locking out the power first. Moving parts can be hidden by materials, and stopped parts can start unexpectedly, causing severe injury. Always stop mixer and lock out power before attempting to remove jammed material or clean. Be aware that the spring-loaded reel arms can spring back unexpectedly, causing injury. DANGER: DO NOT ALLOW OPERATION of this unit

If reel is over full, mixing action will be greatly reduced. Feed must not pile up between the reel and the side of the mixer. This causes a buildup of pressure, increases the power requirements of the mixer, and can cause pipes to bend. Load hay on the auger side of the mixer. This keeps hay from being caught between the reel pipes and side of mixer during initial loading. Break up bales before loading. Move reel cross pipes to the inner setting by compressing the springs and adding bolts and l

If the strips become bent back, they can be unbolted and turned around to improve clean out. Upper Auger Knives can be turned over for use of a new cutting edge and should be periodically sharpened, or replaced if they are no longer sufficiently breaking up material. Lower auger knives can be rotated several times before sharpening or replacement is required. Motor fan guard must be kept clean to allow sufficient air flow for proper motor cooling. Drive belts must be checked for wear and hardnes

Kuhn Knight Inc. will not be responsible for damage caused by overloading, wet hay or foreign objects. WARNING Do not use tough hay (20%-60% moisture) Always use cured, dry hay. Wet hay, foreign objects or overloading may cause binding and damage to the mixer. Do not overload HAY MAXX SYSTEM with too much hay. This can cause bridging over the auger. If this occurs never attempt to release jammed materials or clean out materials from the Hay Maxx area without stopping mixer and locking out power