Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Broan Dateigröße: 2.14 mb Dateiname: Unterrichtssprache:

If the fuse has opened (blown), the green fan setting or light setting indicators will not operate properly when the fan or light buttons are pressed, and the fan and lights will not turn on. A new fuse can be purchased at your local electronic supply store. Use an 8A, 120V, 5 mm diameter, 20 mm long, fast-acting, cartridge-type fuse. To replace the fuse: 1. Disconnect power at service entrance. 2. Remove filters and bottom pan. 3. Remove and inspect fuse. If it is not open (blown), additional diagnostics are needed. PREPARE HOOD LOCATION ROOF CAP V 3%" X 10" or 7" ROUND DUCT (For vertical discharge) 24" - 30" ABOVE COOKING SURFACE HOUSE WIRING (Top or Back of hood) WALL CAP 3%" X 10" DUCT (For horizontal discharge) |l| Determine whether hood will discharge vertically (3%” x 10” or 7” Round), or horizontally (3%” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows. Page 3 (D Use the proper diagram below, for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (5) I 11 V (30" hood) 11%' -14 5/8" (36" hood) —«-14 5/8' 17 V (42" hood) 17 %' {-CABINET FRONT 3%” X 10” VERTICAL DUCTING CABINET BOTTOM ■5%" (30" hood) (36" hood) ■ (42" hood) 67/s' 7T -5%" VERTICAL DUCT ACCESS HOLE 11' & a 1078" 2%" ‘WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) WOOD SHIMS (recessed-bottom cabinets only) 3%” X 10” HORIZONTAL DUCTING CABINET FRONT 13/8" r 4" CABINET ± BOTTOM HORIZONTAL DUCT ACCESS HOLE -5%'- 11 5/8" (30" hood) ■14 %" (36" hood)-17 %" (42" hood) HOOD MOUNTING SCREWS (5) -5%- ■ 67/8' 11 5/8" (30" hood) -14 %" (36" hood) 17 %" (42" hood) CENTER LINE ELECTRICAL ACCESS HOLE (in wall) HOOD MOUNTING SCREWS (5) 11 V (30" hood) 11 V (30" hood) -14 V (36" hood)-' " 17 V (42" hood) f CABINET FRONT 7-IN. ROUND DUCTING -14 V (36" hood)-17 V (42" hood) 107/8" WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) 2 * Note the extra wood shim and mounting screw near the cabinet front, on the cabinet center line. BR6AN MODELS QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW PREPARE THE HOOD |~3~| Remove parts bag from inside the foam packaging end cap. |~4~| Remove all protective polyfilm from the hood (stainless steel hoods only). [~5~| Remove the Aluminum Filters from the hood. Page 4 7 | Remove 2 Screws holding Damper / Duct Connector to hood. Remove damper/duct connector from inside the hood. FOR DUCTED INSTALLATIONS - Skip to Step 12. |~8~| NON-DUCTED INSTALLATION ONLY: From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers. |~9~| NON-DUCTED INSTALLATION ONLY: Remove 2 Screws holdi...

Herunterladen

Geben Sie zwei Ziffern: