Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Broan Dateigröße: 2.14 mb Dateiname: Unterrichtssprache:

For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows. Page 3 (D Use the proper diagram below, for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (5) I 11 V (30" hood) 11%' -14 5/8" (36" hood) —«-14 5/8' 17 V (42" hood) 17 %' {-CABINET FRONT 3%” X 10” VERTICAL DUCTING CABINET BOTTOM ■5%" (30" hood) (36" hood) ■ (42" hood) 67/s' 7T -5%" VERTICAL DUCT ACCESS HOLE 11' & a 1078" 2%" ‘WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) WOOD SHIMS (recessed-bottom cabinets only) 3%” X 10” HORIZONTAL DUCTING CABINET FRONT 13/8" r 4" CABINET ± BOTTOM HORIZONTAL DUCT ACCESS HOLE -5%'- 11 5/8" (30" hood) ■14 %" (36" hood)-17 %" (42" hood) HOOD MOUNTING SCREWS (5) -5%- ■ 67/8' 11 5/8" (30" hood) -14 %" (36" hood) 17 %" (42" hood) CENTER LINE ELECTRICAL ACCESS HOLE (in wall) HOOD MOUNTING SCREWS (5) 11 V (30" hood) 11 V (30" hood) -14 V (36" hood)-' " 17 V (42" hood) f CABINET FRONT 7-IN. ROUND DUCTING -14 V (36" hood)-17 V (42" hood) 107/8" WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) 2 * Note the extra wood shim and mounting screw near the cabinet front, on the cabinet center line. BR6AN MODELS QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW PREPARE THE HOOD |~3~| Remove parts bag from inside the foam packaging end cap. |~4~| Remove all protective polyfilm from the hood (stainless steel hoods only). [~5~| Remove the Aluminum Filters from the hood. Page 4 7 | Remove 2 Screws holding Damper / Duct Connector to hood. Remove damper/duct connector from inside the hood. FOR DUCTED INSTALLATIONS - Skip to Step 12. |~8~| NON-DUCTED INSTALLATION ONLY: From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers. |~9~| NON-DUCTED INSTALLATION ONLY: Remove 2 Screws holding Non-Duct Plate to Non-Duct Plenum and remove plate. [ÏÏÏ] NON-DUCTED INSTALLATION ONLY: Insert short end of Non-Duct Plate into Non-Duct Plenum Slot. Attach with 2 Screws removed in Step 9. [ïï~| NON-DUCTED INSTALLATION ONLY: Purchase a set of (2) non-ducted filters for 30” wide hoods (Model BPPF30) & 36” wide hoods (Model BPPF36) or a set of (3) non-ducted filters for 42” wide hoods (Model BPPF42) from your local distributor or retailer. Attach the non-ducted filters to the aluminum mesh filters following instructions packed with the non-ducted filters. FOR NON-DUCTED INSTALLATIONS - Skip to “INSTALL THE HOOD" BROAN MDLS [T2~ DUCTED INSTALLATION ONLY: Remove 3%” x 10 vertical, 3%” x 10” horizontal, or 7-inch round knockout plate(s) as appropriate for your ducting method. R3J DUCTED INSTALLATION ONLY: Attach 314” x 10” Damper/...

Herunterladen

Geben Sie zwei Ziffern: