Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Desa Dateigröße: 1.98 mb Dateiname: Unterrichtssprache:

Use only 3 wire cord type (3 prong plug) marked for outdoor use. RESETTESTWARNINGGFCI Cord Adapter Figure 1 - GFCI Options Test and Reset Buttons PLUG ADAPTER IMPORTANT: This product must be used on a grounded supply circuit. An adapter as shown in Figure 2 is available for connecting three-prong grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Grounded Outlet Box Figure 2 - Plug Adapter Metal Screw Cover of 115423-01A GENERAL INFORMATION ARRANGEMENT OF MANUAL This manual contains information and service procedures to assist the service technician in understanding and correcting problems on DESA Heating Products Umbrella Stand and Electric Foot Warmer. The first section of the manual contains basic information concerning the operation of the different components in the heater. This information should be reviewed by service personnel to provide a basic understanding of how the components function in the working system. The Troubleshooting section of this manual is intended to provide a quick reference concerning conditions which result in customer complaints. These procedures will help the service technician quickly diagnose a malfunctioning heater. The illustrations in this manual may not necessarily depict the actual heater model and are intended for reference ONLY. TECHNICAL SERVICE DEPARTMENT The Technical Service Department, located in Bowling Green, Kentucky, is committed to assisting our Authorized Service Centers to increase their service knowledge so that they can provide prompt, efficient service. This Service Manual covers the majority of problems that are associated with the heaters. However, as with any product, certain problems can arise which have not been covered. If such problems arise, please call the Technical Service Department.s number, 1-866-672-6040 or visit our website at to address these technical problem areas. If you need assistance for ordering parts, billing questions, etc. you should contact 1-866-672-6040. SERVICE PREPARATION A clean work area at the start of each job is essential for efficient service work. Heaters which are extremely dirty should be cleaned prior to service. Cleaning will occasionally uncover the problem area. Tools needed for the job should be obtained before work is started. Delays resulting from locating tools result in lost time and wages. Use caution and common sense when working on a heater. Always remember that electrical parts can result in potential shock. Heater parts are hot during operation, which could result in burns. TOOLS REQUIRED In addition to common hand tools, the service shop should have the following tools and instruments for proper repairing of the heaters. These instruments will be referred to throughout this manual. INSTRUMENT RANGE 1/4" Nut Driver N/A 3/16" Nut Driver N/A 11/32" Nut Driver N/A 1/8" Allen Wrench N/A 3/4" Open end wrench N/A Torque Wrench N/A Multimeter* 0-250 VAC/0-200 Ohm *Available at most electronic stores. Multimeter PRODUCT IDENTIFICATION Body Lighted On/Off SwitchPower Cord Thumb Screw Warm Air Exhaust Air Intake (opening to bottom of warmer) Tip Switch Push Rod Access to Thermal Limit Switch Air Intakes (Bottom View) Figure 3 - Umbrella Stand Warmer 115423-01A INSTALLATION WIRING DIAGRAM 1. Locate product under outdoor patio table on POWER PLUG 120V 60Hz hard, level, dry surface. Post of tip over switch must be on solid surface for product to work. Listen for the “click”. See Figure 3 for switch location. 2. Slowly lower umbrella pole into product. Do not drop pole, it may damage product. 3. Tighten thumb screw of product to secure pole. Pole will be approximately 7 inches higher than if used without this product. NL L GREEN BLACK NWHITEHEATING ELEMENT BLACK BLACK BLACK BLACK WHITEWHITE 4. Make sure the product is in the OFF position before plugging into a grounded GFCI protected 120V 60 HZ outlet. 5. Avoid overloading your circuit by not using other high wattage products in the same outlet. At 1500 watts, this unit draw 12.5 Amps. OPERATION IMPORTANT: Review andunder- ON/OFF MANUAL RESET SWITCH THERMAL LIMIT TIP SWITCH SWITCH MOTOR stand the warnings in the Safety Information section, page 2. They are needed to safely operate this product. Follow all local ordinances and codes when using this product. 1. Push lighted ON/OFF switch. 2. The power light will remain lit during operation. 3. Stay back from product until all water or debris has blown clear. 4. Product will warm in a few minutes. CLEANING DURING SEASON CARE Always unplug the product before moving or cleaning. 1. Do not disassemble. Carefully wipe the exterior of unit with a soft, damp cloth. 2. After cleaning, be sure to completely dry the unit with a cloth or towel. AFTER SEASON CARE Store product indoors in a dry location. No maintenance is required for this product. GREE...

Herunterladen

Geben Sie zwei Ziffern: