Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to personal injury. CAUTION, without the safety alert symbol, is used to address practices not related to personal injury. READ AND UNDERSTAND ALL INSTRUCTIONS When using this product, safety precautions should always be followed including the following: General Safety Do not use this product for other than its 1. intended use. Inspect before use. Do not use if parts are loose or damaged. Maintain labels and nameplates on the 2. product. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. This product is not a toy. Keep it out of 3. reach of children when children are not being closely supervised. Make sure to install this product on a 4. clean, dry, flat, level surface capable of supporting the weight of the product and its contents. Wear ANSI-approved safety 5. impact goggles and heavy-duty work gloves when assembling this product. Do not exceed the total weight capacity 6. of (400 pounds). Also, make sure the weight is distributed evenly on each Bench. Be aware of dynamic loading. Dropping or bouncing on bench may briefly create excess load causing product failure. Notice Caution Danger WARNING Caution Never allow people or animals to stand 7. or climb on this product. Pinch point warning: Use caution to 8. avoid pinching fingers when assembling and setting up this unit. Adults only should perform the assembly 9. and set-up of this product. When in use, make sure all Legs of the 10. product are flat on the ground. The warnings, precautions, and 11. instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Specifications Construction Material Unfinished Fir Yellow/Green Zinc Plated Steel Bolts, Washers, Nuts, and Screws Weight Capacity 400 Pounds Total (Distributed Evenly) Umbrella Hole Diameter 1-5/8” Waterproof Water Resistant No Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Assembly Note: For additional information regarding the parts listed in the following pages, refer to the accompanying illustrations. Attach the two Folding Beams (2) 1. flush to the inner side of the Table Top (5), using six Bolts each with two Washers and one Nut (9). (See Figure A.) NOTE: 2. The Bolts and Washers (9) should be inserted from the outside of the Table Top (5) into the Folding Beams (2). (See Figure A.) Place and align the Short Bench Top (8) 3. flush on the two Bench Supports (4). (See Figure B.) Fasten the eight Screws (11) into the 4. pre-drilled holes on the Short Bench Top (8) to the Bench Supports (4). (See Figure B.) FIGURE A TABLE TOP (5) FOLDING BEAM (2) BOLTS, WASHERS, NUTS (9) FIGURE B SCREWS (11) SHORT BENCH TOP (8) BENCH SUPPORT (4) Turn the assembled Bench upside down.5. Position the Diagonal Supports (7) so 6. one end is against the longer cross beam of Bench Support (4) legs. Then align the other end so it is flush to the wood edge next to the center gap of the Short Bench Top (8). The two Diagonal Supports (7) need to be attached at opposite sides of the bench gap, using three Screws (11) per Support. (i.e., one support will be attached to one bench slat, and the other bench slat will be attached to the other bench support. (See Figure C.) NOTE: 7. There are no pre-drilled holes for the Screws (11) in the bench slat or Bench Supports (4). Instead, there are guide marks in the wood to indicate where the Screws must be inserted. (See Figure C.) Set the Table on its side.8. Attach the Folding Beams (2) to the 9. outside edge of the Bench Supports (4), using two Bolts, each with four Washers, and one Nut (10). (See Figure D.) Hold the Table securely in its standing 10. position. Attach the two Table Legs (1) to the 11. Table Top (5) by inserting two Bolts each, with four Washers and one Nut (10) into the pre-drilled hole at the rounded end of the Table Legs. NOTE: One pre-drilled hole still remains below the Table Legs. (See Figure E.) Attach the two Arm Rests (3) to the Table 12. Legs (1), using two Bolts, each with four Washers and one Nut (10). (See Figure F.) Place the Long Bench Top (6) on the 13. Table Legs (1). Make sure the longer bar underneath the Long Bench top is toward the outside. (See Figure G.) Fasten the eight Screws (11) into the 14. pre-drilled holes in the Long Bench Top (6) to the Table Legs (1). (See Figure G.) TABLE TOP...