Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
OUTDOOR EXTENSIONS CORDS. 15. When the equipment is operated outdoors, use only extension cords intended for outside use. See chart under “Extension Cords" for the proper AWG rating depending on the length of the cord(s) being used. STAY ALERT. 16. Watch what you are doing; use common sense. Do not operate any tool when you are tired. CHECK DAMAGED PARTS.17. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn on and off properly. GUARD AGAINST ELECTRIC SHOCK.18. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. REPLACEMENT PARTS AND 19. ACCESSORIES. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. DO NOT OPERATE TOOL IF UNDER 20. THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. UNPACKING If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Part Description Qty 1 Body 1 N/A Handle Assembly 1 6 Plate 1 10 Rack 1 ASSEMBLY Mounting the Body to Your Workbench Select a place on your workbench to 1. mount the Arbor Press. Purchase hardware to mount your Arbor 2. Press to your workbench. Bolt length will be the thickness of your workbench plus 2-1/2” of length for the Arbor Press BODY (#1). Body (#1) Mounting HoleMounting Hole(not shown) Figure 1 -- Location of Mounting Holes 3. Use the two mounting holes in the BODY of the Arbor Press as a template as shown in Figure 1. Mark and Drill holes in your workbench. Place the BODY over the holes in the 4. workbench and insert the bolts through the holes. Thread on the nuts and tighten. Arbor Press Assembly Plate (#6) Body (#1) Spring Pin (#7) (not shown) Figure 2 -- Installing the Plate 1. Place the PLATE (#6) onto the Base of the BODY (#1) as shown in Figure 2. Insert the SPRING PIN (#7) into the hole in the BODY. Rack (#10) Rack TeethBody (#1) Cover (#8) Figure 3 -- Installing the Rack 2. Insert the RACK (#10) down through the top of the BODY as shown in Figure 3. Make sure the teeth of the RACK are towards the rear of the BODY as shown in the Figure. Unwrap the Handle Assembly and discard 3. the protective padding. Handle AssemblyBody (#1) Figure 4 -- Installing the Handle Assembly 4. Insert the GEAR (#14) section of the Handle Assembly into the side of the Arbor Press as shown in Figure 4. The GEAR will only fit into the side shown in the Figure. You may have to rotate the Handle Assembly 5. slightly to get the teeth of the GEAR to mesh with the teeth of the RACK. Rack (#10) Ring (#5) Handle AssemblyFigure 5 -- Attaching the Ring 6. Slide the RING (#5) onto the protruding end of the GEAR as shown in Figure 5. Tighten the SCREW (#4) on the RING to secure the GEAR and Handle Assembly. Your Arbor Press is ready for use.7. OPERATION Adjusting the Handle Assembly Determine if you will need a moderate or 1. large amount of leverage for the job. Lock Pin (#11) Shaft (#15) Figure 6 -- Adjusting the Shaft 2. Loosen the LOCK PIN (#11) by turning it as shown in Figure 6. This will allow you to adjust the length of the SHAFT (#15). Adjust the length of the SHAFT to 3. suit your needs. If a large amount of leverage is needed for your press job, lock the SHAFT in the extended position. If a moderate amount of leverage is needed, position the SHAFT in the middle of the GEAR. Tighten the LOCK PIN to secure the 4. Handle Assembly. The following Steps show the SHAFT in the extended position. Using the Arbor Press Shaft (#15) Rack (#10) Plate (#6) Figure 7 -- Raising the Rack 1. Raise the RACK (#10) up by turning the Handle Assembly as shown in Figure 7. Turn the PLATE (#6) until the appropriate 2. width opening is centered under the RACK. The appropriate width depends upon what you are using the press for. If you do not want an opening beneath the RACK, rotate the PLATE until one of the four solid parts of the PLATE is underneath the RACK. Place the part you need to press onto 3. the PLATE. Turn the Handle Assembly to lower the 4. RACK until the top of the RACK contacts the press part. Place downward pressure on the Handle 5. Assembly to press the part as needed. Release pressure on the Handle 6. Assembly and raise the RACK to remove the part. Parts list and Assembly diagram Part Description Qty 1 Body 1 2 Bolt 8 3 Nut 6 4 Screw 1 5 Ring 1 6 Plate 1 Part Description Qty 7 Sprin...
Dieses Handbuch ist für folgende Modelle:Möbel - 3552 (662.45 kb)