Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
1 x CD In connector . 1 x S/PDIF Out header . 2 x USB 2.0/1.1 headers . 1 x IEEE 1394a header . 1 x serial port header . 1 x power LED header . 1 x chassis intrusion header Back Panel . 1 x PS/2 keyboard port Connectors . 1 x PS/2 mouse port . 1 x coaxial S/PDIF Out connector . 1 x optical S/PDIF Out connector . 8 x USB 2.0/1.1 ports . 2 x IEEE 1394a ports . 1 x RJ-45 port . 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone) I/O Controller . iTE IT8720 chip Hardware Monitor . System voltage detection . CPU/System temperature detection . CPU/System fan speed detection . CPU overheating warning . CPU/System fan fail warning . CPU/System fan speed control (Note 3) BIOS . 2 x 8 Mbit flash . Use of licensed AWARD BIOS . Support for DualBIOSTM . PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b Unique Features . Support for @BIOS . Support for Download Center . Support for Q-Flash . Support for EasyTune (Note 4) . Support for Xpress Install . Support for Xpress Recovery2 . Support for Virtual Dual BIOS . Support for Easy Energy Saver (Note 5) Bundled Software . Norton Internet Security (OEM version) Operating System . Support for Microsoft® Windows® 7/Vista/XP Form Factor . ATX Form Factor; 30.5cm x 21.5cm GA-M720-US3 Motherboard - 12 - 1-3 Installing the CPU and CPU Cooler Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage. • Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. • Apply an even and thin layer of thermal grease on the surface of the CPU. • Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur. • Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. 1-3-1 Installing the CPU A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU. AM2+/AM2 CPU A Small Triangle Mark AM2 Socket Denotes Pin One of the Socket A Small Triangle Marking Denotes CPU Pin One - 13 - Hardware Installation Step 2: Align the CPU pin one (small triangle marking) with the triangle mark on the CPU socket and gently insert the CPU into the socket. Make sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one finger down on the middle of the CPU, lowering the locking lever and latching it into the fully locked position. Step 1: Completely lift up the CPU socket locking lever. CPU Socket Locking Lever Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the CPU orientation if this occurs. B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. GA-M720-US3 Motherboard - 14 - Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU. 1-3-2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU. Step 2: Place the CPU cooler on the CPU. Step 4: Turn the cam handle from the left side to the right side (as the picture above shows) to lock into place. (Refer to your CPU cooler installation manual for instructions on installing the cooler.) Step 3: Hook the CPU cooler clip to the mounting lug on one side of the retention frame. On the other side, push straight down on the the CPU cooler clip to hook it to the mounting lug on the retention frame. Step 5: Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard. - 15 - Hardware Installation 1-4 Installing the Memory Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest memory support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. • Memory modules have a foolproof design. A memory module can be installed...