6. Halten Sie das Kabel vom Schnittbereich fern. 7. Das Kabel nicht um scharfkantige Objekte ziehen. 8. Immer zuerst die Stromversorgung unterbrechen, bevor ein Stecker, Kabelverbinder oder ein Verlangerungskabel entfernt wird. 9. Den Rasenmaher ausschalten, den Stecker aus der Steckdose ziehen und das elektrische Versorgungskabel auf Beschadigungen oder Alterungsanzeichen uberprufen, bevor das Kabel zur Lagerung aufgewickelt wird. Ein beschadigtes Kabel darf nicht repariert werden; es mu. mit e

Selbst mit einer solchen Schutzvorrichtung kann keine 100-prozentige Sicherheit garantiert werden. Deshalb müssen jederzeit die entsprechenden Sicherheitsvorschriften beachtet werden. Die Fehlerstrom-Schutzvorrichtung bei jeder Verwendung überprüfen. 2. Vor der Verwendung muß das Kabel auf Beschädigungen überprüft werden. Bei Anzeichen einer Beschädigung oder Alterung muß es ausgewechselt werden. 3. Den Rasentrimmer nicht verwenden, wenn die elektrischen Kabel beschädigt oder abgenutzt sind.

Warning: The cutting line continues to rotate after the machine has been switched off. 360. 10m Electric Cable with moulded on plug Guard (with bolt and nut) Instruction Manual Adjustable Shoulder Harness Cable Management Cable Management Hexagon Drive Tool Handle Clamp Switch Handle Steady Handle Shoulder Harness Location Lock-off button 3. Do not use the product if the electric cables are non-slip footwear. damaged or worn. 5. Do not walk backwards when operating, you could 4. Immediately disc

To fit spool and line complete: 1. Remove old spool. 2. Place new spool into spoolholder with cut out area of the spool in line with eyelet as shown in figure V. 3. Release line from cleat and feed line through eyelet (V). • Ensure spool is fully located by gently rotating it dur- ing fitment, whilst keeping the spoolholder steady. 4. Refit the cap. To fit nylon line only: • Remember! Your product is designed to use only nylon line with a maximum diameter of 1.5mm. Use only genuine Flymo nylon l

Actual use and your experience will determine the frequency of required maintenance. Saw chain sharpening procedure • A Low-kickback Chain • Low-vibration Chain • Narrow-kerf Chain FILING TOOLS FOR FILING Description 4.5 mm Round file 4.5 mm Assembled file guide .025 inch Drop-centre depth-gauge tool Depth-gauge file (flat) Square-ground Filing WHO SHOULD PERFORM SQUARE-GROUND FILING? Most chain saw users will probably never need to use square ground chain, nor learn to perform square ground fil

XPH.E.. .IABA.TE .PO.EKTIKA . Hasznalati utmutato FIGYELEMMEL OLVASANDO } Instrukcja obslugi Przeczytaj uwaznie 1 5 9 49 PN 248722 0 0 ¤ . E A ‰ „ ‹‚ · › fi ‡ fl 96dBA 15m1 2 Fig. 2-2 fl . ¤ ‹ › ‡fi · ‚ Fig. 2-1 Fig. 2-3 Fig. 2-4 96dBA 15m1 2 Fig. 2-2 fl . ¤ ‹ › ‡fi · ‚ Fig. 2-1 Fig. 2-3 Fig. 2-4 3 Fig. 3-1 Fig. 3-3 Fig. 3-2 3 Fig. 3-1 Fig. 3-3 Fig. 3-2 4 Fig. 4-1 4 4 Fig. 4-2 Fig. 4-3 Fig. 4-4 Fig. 4-5 Fig. 4-6 Fig. 4-7 ENGLISH g ENGLISH g INDEX Introduction A) General Safety Instructions B) El

Keep others, including children, pets and bystanders outside the 10 metre hazard zone. Stop the trimmer immediately if you are approached. The use of eye protection is recommended to protect against objects thrown by the cutting line. To avoid the possibility of electric shock, do not use in damp or wet conditions. Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Warning: The cutting line continues to rotate after the machine has been switched of

2. To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (E2). 3 Assembly Instructions B1 B2 A1 Double Auto Feed System How the automatic line feed works (F) 1. When initially switching on the trimmer, a small length of line is fed out. 2. A .clattering. noise will be heard when the two nylon lines hit the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise

2. Push into location and turn safety guard in the direction illustrated in Fig B2, until a click is heard and the safety guard is securely locked in position. • ENSURE THE SAFETY GUARD IS SECURELY IN PLACE BY ATTEMPTING TO TWIST GUARD. Steady Handle Assembly (C) 1. Depress the two buttons on the sides of the switch handle. 2. Locate the steady handle over the buttons and release the buttons. 3. Adjust the steady handle to the most comfortable operating position by depressing the buttons and mov

Loop handle installation a) Orient the loop half of the handle as shown on the picture, and place it on the outer shaft of the Power Head. b) Align 4 holes of the second part of the handle with the holes of the loop half. 230V Power Head parts list KEY # DESCRIPTION PART # QTY KEY # DESCRIPTION PART # QTY MOTOR ASSEMBLY 331298 1 31 INLAY (LEFT) 331277 1 MOTOR BRUSH 331253 2 32 WIRE JOINTER 331278 1 BRUSH HOLDER 331254 2 33 POWER CORD 331302 1 HOLDER 331255 2 34 EXTENSION CORD CLIP 331280 1 SCREW