Straight cut 009280 To trim the hedge straight, pull triggers A and B. Vertical cut 009281 Cut upwards with both hands pull the switch triggers B and C and move it in front of your body. Far area cut 009282 To trim the hedge in far area with both hands pull the switch triggers A and C. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Engage the extension cord CAUTION: • Make sure that the extension cord is unplugged to the m

1600/min. Overall length 862 mm (34") 970 mm (38-1/4") 1,042 mm (41") Net weight 3.6 kg (7.9 lbs) 3.7 kg (8.2 lbs) 3.8 kg (8.4 lbs) • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003 USB093-3 IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF

and spray-type lubricating oil. CAUTION: • Do not wash the blades in water. Failure to do so may cause rust or damage on the tool. 7 Removing or installing shear blade Removing or installing shear blade CAUTION: • Before removing or installing shear blade, always be sure that the tool is switched off and unplugged. • When replacing the shear blade, always wear gloves without removing blade cover so that hands and face does not directly contact the blade. Failure to do so may cause personal injur

Always follow safety precautions in the Owner’s and Safety Manual. Improper use can cause serious injury! Preserve this Manual carefully! ATTENTION! Avant d’utiliser le taille-haie DOLMAR, il est important que vous ayez lu et compris ce manuel. Suivez toujours les conseils de securite de ce manuel d’emploi et de securite. Une utilisation incorrecte du taille-haie peut entrainer des blessures graves! Conservez avec soin ce manuel d’emploi! .ADVERTENCIA! Lea y comprenda este manual. Observe siempr

REFUELING METHOD • Loosen the tank cap a little so that there will be no difference in atmospheric pressure. • Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that the refuel port will be oriented upward. (Never refill fuel full to the oil refill port.) • After refueling, securely tighten the tank cap. • If there is any flaw or damage on the tank cap, replace it. • The tank cap is consumable, and therefore should be renewed every two to three years. 10 OPERATION 1. S

THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusio

Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. Do only hand over the Hedge Trimmer together with this manual. AVERTISSEMENT: Afin d’eviter les blessures, l’utilisateur doit lire et comprendre les instructions de ce manuel avec attention avant d’utiliser le taille-haies. Le fabricant se seserve le droit de modifier les specifications sans avertissement prealable. Les specifications peuvent varier d’un pays a l’autre. Lor

995 700 253 (GB) DOLMAR GmbH • Postfach 70 04 20 • D-22004 Hamburg • Germany LT-210 1 Pipe, handle, protector, gear case 2005/11 1 5 6 7 8 3 2 17 18 19 20 21 22 24 25 23 26 27 28 30 16 4 9 10 12 11 14 13 15 29 LT210 1/3 LT-210 PagePos. LT-210LT-250Part No. Notes Description Specifications 1 1 1 381 450 070 GRIP 1 2 1 381 502 800 CONTROL LEVER ASSY INC. 3,5-12 1 3 1 381 501 811 WIRE SET INC. 4 1 4 1 381 501 812 CONTROL CABLE 1 5 1 381 501 805 TUBE 1 6 3 381 350 530 SCREW ASSEMBLY M5X30(SW) 1 7 1

A02, A03 3 *A02 1 374 704 999 HEX. WRENCH 3 *A03 1 381 903 001 PIN 3 *A05 1 381 802 000 NYLON CUTTING HEAD (BUMP& FEED) * NO PICT. Pipe, handle, protector, gear case, carburetor, air cleaner, accessories LT-250 Pipe, handle, protector, gear case, carburetor, air cleaner, accessories LT-250 LT-250 PagePos. LT-210LT-250Part No. Notes Description Specifications 4 1 1 381 100 600 FLEXIBLE PIPE UNIT INCL. FIG. 16 4 2 1 388 100 503 FLEXIBLE SHAFT 4 3 1 388 300 200 GEAR CASE CPL. INCL. FIG. 79 - 86 &10

995 700 252 (GB) DOLMAR GmbH • Postfach 70 04 20 • D-22004 Hamburg • Germany Pipe, handle, protector, carburetor, air cleaner MS-20 C Pipe, handle, protector, carburetor, air cleaner MS-20 C MS-20 C PagePos.MS-20 CMS-22 CPart No. Notes Description Specifications 1 1 1 374 101 000 SHAFT PIPE COMPLETE 1 2 1 374 150 040 SHAFT 1 3 1 374 300 400 GEAR CASE ASS'Y INC. 4,5,6,7,8-16 1 4 1 367 300 300 CUTTER SHAFT SET 1 5 1 381 250 030 BALL BEARING #609ZZ 1 6 1 367 006 999 BALL BEARING 626ZZ 1 7 1 367 010