Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Makita Dateigröße: 3.2 mb Dateiname: 07_01_pn_70001.pdf Unterrichtssprache:

This may result in operator injury. Soil Conditions: Bed shaping will require the least amount of time, power and blade wear when the soil is damp. Pre-wetting the soil may be an option. The sod will cut cleaner and the remaining sod strip will stay intact for easier cleanup if damp. Pre-Marking: Pre-mark the area to be shaped with marking paint or lime to ensure a consistent straight or curved edge. Never use solid objects or string as markers as these items may be thrown by the blade or wrap around the blade shaft. Multiple Passes and Cutting Width: When establishing a new bed or redesigning an existing bed, it is recommended that multiple passes be made. To facilitate removal of sod strips, the passes should be less than 3" (7.6 cm) in width. Speed: A slow walking pace is good for safe operation and accuracy, while maintaining efficiency. Buried Hazards: be constantly aware of the possibility of buried hazards. Check with property owners about possible hazards before using the BedShaper®. A little time spent investigating an area may prevent costly mistakes. Cutting New Beds: First, mark area to show the new bed outline. Then make first cut approximately 1" (2.5 cm) inside the outer border. Operate unit in counter clockwise direction, widening radius 3" (7.6 cm) in each rotation until desired bed size is achieved. Clogging: If clogging occurs, disengage the blade engagement lever. Stop engine, make sure that all moving parts have come to a stop. Disconnect spark plug wire. Raise blade arm lift lever. Remove the two bolts which hold the hinged blade shield in place. Swing shield into servicing position. Danger If unclogging is required, use a dowel or other such object to unclog the blade and shield. When finished unclogging, swing shield back into place and fasten securely with bolts. Check blade nut to insure it is tight. Danger Never attempt to operate machine without blade shield securely fastened. Caution Hot Blade: allow blade to cool before servicing. Blade may be hot enough to cause burns. Little Wonder® 6 Section 5 MAINTENANCE BedShaper® Maintenance Chart- Service Intervals Item Daily 25 Hrs. Yearly Page Visual Inspection ¦ Engine Refer to Engine Manual Clean Blade Shield ¦ 6 Check Wear on Blade ¦ 7 Lubricate Blade Arm Zerk Grease Fittings ¦ 7 Check Drive Belts ¦ 8 Lubricate Blade Shaft & Axle Bearings ¦ 8 Chain Tension ¦ 8 End of Season Cleaning ¦ 8 Table 5-1 ILLUSTRATED INSTRUCTIONS FOR MAINTENANCE Warning Before any maintenance or adjustment to BedShaper® is performed, always remember to: stop engine. Disconnect spark plug wire and allow components to cool before servicing. Clean Blade Shield: 1. Make sure blade is cool. 2. Remove two cover bolts from blade shield. Open hinged shield. 3. Remove debris from shield and behind blade with a dowel or similar object. Never use hand- blade may be sharp. 4. Close shield back into position. Securely fasten shield with two bolts. Never operate without shield securely fastened. Little Wonder® 7 Check Wear of Blade 1. Make sure blade is cool enough to handle (always wear gloves when handling blade). 2. Look for any excessive wear, chipping and abnormal wear. Replace if necessary (see section 6). 3. Check tightness of nut. Never operate machine when nut is not properly tightened. Nut should be tightened to 100 ft. lbs (13.8 kg/m). Check Blade Drive Belt 1. Remove blade (see “change blade”, page 8). 2. Remove bolts from belt drive shield. Remove shield. 3. Check condition of belt for excessive wear, fraying and abnormal conditions. 4. Replace with new belt, if necessary (see section 6). 5. Reinstall belt drive shields, fasten securely with bolts. 6. Replace blade per instructions. Lubricate Blade Shaft & Axle Bearings (x4) (Photo 5-1) 1. Locate and clean fittings. . & . 2. Pump fittings full of grease using a hand pump. Important Do not overfill. Too much pressure will damage . . . Photo 5-1 bearing seals. Lubricate Blade Arm Zerk Grease Fittings 1. Locate and clean fittings on both sides of arm. (Photo 5-1) ..x2 2. Pump fittings full of grease using a hand pump. ADJUSTMENT- DIRT SCRAPER GAP (PHOTO 5-2) 1. Allow blade time to cool. 2. Raise BedShaper® blade lift lever into transport position. 3. Examine gap between blade and dirt scraper. Note: recommended gap is 1/2" (1.3 cm). 4. Adjust gap, if necessary. Loosen the two bolts which secure dirt scraper. Adjust gap to 1/2" (1.3 cm). Snug bolts. 5. Rotate blade at least one full revolution. Check to see that blade does not contact dirt scraper. If contact is made, repeat step and increase gap. Important: dirt scraper must not contact rotating blade. Photo 5-2 6. Tighten bolts on dirt scraper securely. CLEANING- END OF SEASON 1. Remove bolts from all shields. 2. Tilt or remove shields so that internal parts of machine are exposed. Little Wonder® 8 6. Lubricate all fittings with grease and perform 3. Remove dirt and debris from machine using all maintenance checks to prevent corrosion and compressed air. to rea...

Herunterladen

Geben Sie zwei Ziffern: