Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• See also “Changing the general settings (PSM)” on page 20. 1. Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears on the display. 2. Select “B SKIP (Blank Skip)” with . or 4. 3. Select the desired mode with the control dial. The Blank Skip mode alternates between on and off. ON OFF Note: When the tape reaches its end while fast-forwarding, the tape direction will be changed automatically. Playing the current tune repeatedly You can play the current tune repeatedly. (Repeat Play) RPT Each time you briefly press RPT (Repeat) while playing a tape, Repeat Play turns on and off alternately. Lights up when Repeat Play is turned on. Notes: • In the following cases, Blank Skip and Repeat Play may not operate correctly: – Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during tunes. – Tapes with short non-recorded sections. – Tapes with high level noise or humming between tunes. – The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. Prohibiting cassette ejection You can prohibit the cassette ejection and can “lock” a cassette in the cassette compartment. Press and hold TAPE 23 and for more than 2 seconds. “NO EJECT” flashes on the display for about 5 seconds, and the cassette is “locked.” To cancel the prohibition and “unlock” the cassette, press and hold TAPE 23 and for more than 2 seconds again. “EJECT OK” flashes for about 5 seconds, and this time the cassette is “unlocked.” ENGLISH 13 ENGLISH ENGLISH SOUND ADJUSTMENTS Adjusting the sound You can adjust the treble/bass sound and the speaker balance. 2 1 Equalization pattern indicator 1 Select the item you want to adjust. Indication To do: Range BAS (Bass) Adjust the bass –06 (min.) — +06 (max.) TRE (Treble) Adjust the treble –06 (min.) — +06 (max.) FAD (Fader)* Adjust the front and rear speaker balance R06 (rear only) — F06 (front only) BAL (Balance) Adjust the left and right speaker balance L06 (left only) — R06 (right only) VOL (Volume) Adjust the volume 00 (min.) — 50 (max.) Note: * If you are using a two-speaker system, set the fader level to “00.” 2 Adjust the level. Equalization pattern changes as you adjust the bass or treble. Note: Normally the control dial works for volume adjustment. So you do not have to select “VOL” to adjust the volume level. 14 Turning on/off the loudness function The human ear is less sensitive to low and high frequencies at low volumes. The loudness function can boost these frequencies to produce well-balanced sound at low volume level. 1 LOUD Turn on or off the loudness function. Each time you press LOUD, the loudness function turns on and off alternately. ENGLISH 15 ENGLISHENGLISH Using the Sound Control Memory You can select and store a preset sound adjustment suitable to each playback source. (Advanced SCM) Selecting and storing the sound modes Once you select a sound mode, it is stored in memory, and will be recalled every time you select the same source. A sound mode can be stored each of the following sources — FM1, FM2, FM3, AM, tape, and external components. • If you do not want to store the sound mode separately for each playback source, but want to use the same sound mode for all the sources, see “Canceling Advanced SCM” on page 21. “Link” indicator SCM SCM Select the sound mode you want. Each time you press the button, the sound mode changes as follows: • If the “Link” indicator is lit on the display (with “SCM LINK” set to “LINK ON” — see page 21), the selected sound mode can be stored in memory for the current source, and the effect applies to the current source. • If the “Link” indicator is NOT lit on the display (with “SCM LINK” set to “LINK OFF”), the selected sound mode effect applies to any source. Indication For: Preset values Bass Treble Loudness SCM OFF (Flat sound) 00 00 On BEAT Rock or disco music +02 00 On SOFT Quiet background music +01 –03 Off POP Light music +04 +01 Off 16 Recalling the sound modes Source buttons CD-CH FM/AM TAPE Select the source while the “Link” indicator is lit on the display. The “Link” indicator starts flashing, and the sound mode stored in memory for the selected source is recalled. Sound mode indicator Equalization pattern of the selected sound mode appears. Notes: • You can adjust each sound mode to your preference, and store it in memory. If you want to adjust and store your original sound mode, see “Storing your own sound adjustments” on page 18. • To adjust the bass and treble reinforcement levels or to turn on/off the loudness function temporarily, see pages 14 and 15. (Your adjustments will be canceled if another source is selected.) ENGLISH 17 ENGLISHENGLISH Storing your own sound adjustments You can adjust the sound modes (BEAT, SOFT, POP: see page 16) to your preference and store your own adjustments in memory. 3 2 2 1,4 1 Call up the sound mode you want to adjust. See page 16 for details. 2 To adjust the bass or treble sound le...