Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
– Tapes with high level of noise or humming between tunes. – The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. ENGLISH 17 ENGLISH Other convenient tape functions Skipping the blank portions on the tape You can skip blank portions between the tunes (Blank Skip). When this function is on, the unit skips blank portions of 15 seconds or more, fast-forwards to the next tune, then starts playing it. • See also “Changing the general settings (PSM)” on page 22. 1 Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see page 23.) 2EPress . or 4 to select “B. SKIP” (blank skip). 3 Turn the control dial clockwise to select “ON.” Now Blank Skip is activated. 4EPress SEL (select) to finish the setting. Playing the current tune repeatedly You can play the current tune repeatedly (Repeat Play). Press RPT (repeat/Dolby B) while playing a tune you want to hear over again. Each time you briefly press the button, Repeat Play turns on and off alternately. Lights up when Repeat Play is turned on. When the tune has been played, the tape is automatically rewound to the beginning of that tune and the same tune will be played again. To cancel Repeat Play, press RPT again so that the RPT indicator goes off. Note: In the following cases, Blank Skip and Repeat Play may not operate correctly: – Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during tunes. – Tapes with short non-recorded sections. – Tapes with high level noise or humming between tunes. – The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. To cancel Blank Skip, repeat the same procedure and select “OFF” in step 3 by turning the control dial counterclockwise. 18 SOUND ADJUSTMENTS Adjusting the sound You can adjust the sound characteristics to your preference. 1ESelect the item you want to adjust. Each time you press the button, the adjustable items change as follows: VOL LOUD** BAS (bass) TRE (treble) FAD (fader) BAL (volume) (loudness) (balance) Indication To do: Range BAS Adjust the bass. –06 (min.) | +06 (max.) TRE Adjust the treble. –06 (min.) | +06 (max.) FAD* Adjust the front and rear speakerbalance. R06 (Rear only) | F06 (Front only) BAL Adjust the left and right speakerbalance. L06 (Left only) | R06 (Right only) LOUD** (only for KS-FX915R) Boost low and high frequencies to produce a well- balanced sound at low volume level. LOUD ON | LOUD OFF VOL Adjust the volume. 00 (min.) | 50 (max.) * If you are using a two-speaker system, set the fader level to “00.” **only for KS-FX915R 2EAdjust the level. To increase the level. To decrease the level. Equalization pattern changes as you adjust the bass or treble. Note: Normally, the control dial works as the volume control. So you do not have to select “VOL” to adjust the volume level. Turning on/off the loudness function (only for KS-FX815) LOUD The human ear is less sensitive to low and high frequencies at low volumes. The loudness function can boost these frequencies to produce a well-balanced sound at low volume levels. Each time you press LOUD, the loudness function turns on/off alternatively. ENGLISH 19 ENGLISH Using the sound control memory You can select and store a preset sound adjustment suitable for each playback source (Advanced SCM). Selecting and storing the sound modes Once you select a sound mode, it is stored in memory. It will be recalled every time you select the same source and will be shown on the display. A sound mode can be stored for each of the following sources — FM1, FM2, FM3, AM, tape and external components. • If you do not want to store the sound mode separately for each playback source, but want to use the same sound mode for all the sources, see “To cancel Advanced SCM – SCM LINK” on page 24. Select the sound mode you want. Ex.: When you select “BEAT” Each time you press the button, the sound mode changes as follows: SCM OFF (BEAT) (SOFT) (POP) • When “SCM LINK” is set to “LINK ON,” the selected sound mode can be stored in memory for the current source and the effect applies only to the current source. Each time you change the playback source, the SCM indicator flashes on the display. • When “SCM LINK” is set to “LINK OFF,” the selected sound mode effect applies to any source. Indication For: Preset values BAS TRE LOUD BEAT Rock or disco music +02 00 ON SOFT Quiet background music +01 –03 OFF POP Light music +04 +01 OFF SCM OFF (Flat sound) 00 00 ON Recalling the sound modes When “SCM LINK” is set to “LINK ON,” select the source. Each time you change the playback source, the SCM indicator flashes on the display. The sound mode stored in memory for the selected source is recalled. Notes: • You can adjust each sound mode to your preference, and store it in memory. If you want to adjust and store your original sound mode, see “Storing your own sound adjustments” on page 2...
Dieses Handbuch ist für folgende Modelle:Kompakt-Stereoanlagen - KS-FX815 (5.79 mb)