Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Honda Power Equipment Dateigröße: 2.01 mb Dateiname: Unterrichtssprache:

--1’ I/ -1 TO LOCK LOCKED POSITION som, lower the motor and operate the boat at full speed. If the bow is exces- sively low stop the boat and motor. Tilt the motor up and raise the transom angle adjusting rod one more hole away from the transom and retest. The optimum boat trim is when the boat is parallel with the water. The transom angle adjusting rod stops the motors forward movement. The motor should never be operated with the transom angle adjusting rod removed. 3. CONTROLS & INSTRUMENTS (common) Fuel Cap/Gauge/Vent Knob VENT KNOB I GAUGE FUEL FILLER CAP The fuel gauge is part of the fuel cap. The fuel cap vent knob controls air entering and leaving the fuel tank. When refilling the fuel tank, turn the vent knob counterclockwise to the open position and remove the fuel cap. Before transporting, storing or refill- ing the fuel tank inspect the condition of the fuel cap gasket and replace if nticessary. Before transporting or storing the fuel tank turn the vent knob fully clock- wise to the closed position. extremely flammable, and gaso- line vapor can explode, causing serious injury or death. Do not smoke or allow flames or sparks in your working area. KEEP OUT OF REACH OF CHILDREN. Over-Rev Limiter This outboard motor is equipped with an engine over-rev limiter which limits the maximum engine rpm. This over- rev limiter protects the engine from mechanical damage. The over-rev limiter may be activated by putting the propeller in a light load condition or propeller ventilation. When the over-rev limiter is activated the engine rpm will become unstable or erratic. Should this occur reduce the throttle opening and wait for the engine rpm to stabilize then increase the throttle opening. 4. INSTALLATION Installation It is your responsibility to choose a boat suitable for the motor. DO NOT OVERPOWER THE BOAT Do not install an outboard motor that exceeds the recommended maximum horsepower for the boat. Refer to the boat certification plate for the maxi- mum recommended horsepower for the boat. For most boat applications, the motor should have a horsepower which provides 80% of the maximum recom- mended horsepower for the boat. If the certification plate information is not available, contact the boat dealer. The BF25A/30A must be installed on transoms which have the following minimum or maximu thickness. Boat Transom Thickness Minimum = 1.38 in (35 mm) Maximum = 2.24 in (57 mm) STERN CENTER LINE Installation position Install on the stern center line. Installation height For proper propeller depth and engine cooling, the boat and outboard motor transom height must match. Three outboard motor transom heights are available. Match your boats tran- som height to the outboard motor transom height shown below. Outboard Motor Type Transom Height Short 16.97 in (43 I mm) Long 21.73 in (552 mm) Extra Long 24.88.in (632 mm) @ MOTOH TRANSOM HEIGHT @ BOAT TRANSOM HEIGHT @I O-2 in (O-50 mm) @ ANTI-VENTLATION PLATE The anti-ventilation plate should be O-2 inches below the bottom of the boat. With the boat in the water, loaded and motor off, the anti-ventilation plate should be about 4 inches below the surface of the water. -1 Running the outboard motor without sufficient cooling water will damage the water pump and overheat the engine. 4. INSTALLATION Motor attachment STERN CLAMP SCREW SAFETY ROPE Attach the stem bracket to the transom and tighten the clamp screws. picq l Before operating the boat, check the tightness of the clamp screws. l Tie a rope through the hole in the stern bracket and secure the other end of the rope to the boat. This will prevent accidental loss of the motor. TRANSOM BOARD To prevent the outboard motor from falling accidentally, you may further secure the stem bracket to the transom board with the optional Mounting Bolt/ Nut Kit. Good quality stainless steel commercially available bolts, nuts and washers may also be used. Before installing the bolts, be sure to apply sealant to the bolt holes. This modification should be made by your authorized Honda Marine dealer. For battery handling and installation information refer to pages 79. 4. INSTALLATION Engine Cover Removal/Installation FRONT SIDE GINE COVER To remove, release the engine cover latch and remove the engine cover. To install, position the engine cover over the engine and hook and lock the latch. 5. PRE-OPERATION CHECKS Engine Oil Engine oil is a major factor affecting engine performance and service life. @@@ Running the engine with insufficient oil can cause serious en&e damage. Recommended oil Use high-detergent, premium quality Cstroke engine oil, certified to meet or exceed U.S. automobile manufac- tures’ requirements for American Petroleum Institute (API) Service Classification SG, SH. Engine oils classified SG, SH will show these designations on the container. Select the appropriate viscosity for the average temperature in your area. SAE low-30 is recommended for general, all-temperature use (BF25A). SAE 5W-30 is recommended for gen- er...

Herunterladen

Geben Sie zwei Ziffern: