General Safety Rules For Bench Top Tools Work Area . Keep work area clean and well lit. Cluttered benches and dark areas invite accidents. . Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. . Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control. . Store idle tools out of reach of children and other untrained

BM 2610924645 08-04 E 9/2/04 10:48 AM Page 1 BM 2610924645 08-04 E 9/2/04 10:48 AM Page 1 For English .Habla espanol? Parlez-vous francais? See page 2 Ver pagina 38 Voir page 74 4212L Operating/Safety Instructions Instrucciones de funcionamiento y seguridad Consignes de fonctionnement/securite IMPORTANT: IMPORTANTE: IMPORTANT : Read Before Using Leer antes de usar Lire avant usage 1-877-BOSCH99 (1-877-267-2499) Call Toll Free for Consumer Information & Service Locations Llame gratis para obtener

(These detents are only for use with crown moldings that have a 38°“spring angle”.) NOTE: These detents cannot be used with 45° crown molding. — See also pages 29 & 30 for miter and bevel angle charts for cutting crown moldings that have 38° and 45° spring angles (and the material is laid flat on the miter saw base). Each chart lists the exact miter and bevel settings required for a wide range of corner angles. — Even though these angles are standards, most rooms do not have angles of exactly 90

Work Area KEEP CHILDREN AWAY Do not let visitors contact tool or extension cord. All visitors should be kept away from work area. KEEP WORK AREAS CLEAN Cluttered areas and benches invite accidents. MAKE WORKSHOP CHILD-PROOF With padlocks, master switches. AVOID DANGEROUS ENVIRONMENTS Don’t use power tools in damp or wet locations. Keep work area well lit. Do not expose power tools to rain. Do not use tool in presence of flammable liquids or gases. Personal Safety KNOW YOUR POWER TOOL Read and un

NOTE AND FOLLOW SAFETY INSTRUCTIONS THAT APPEAR ON THE FRONT OF YOUR TABLE SAW. Additional Safety Rules 12. THINK SAFETY WARNING! Some dust created by power sanding, SAFETY IS A COMBINATION OF OPERATOR COMMON sawing, grinding, drilling, and other SENSE AND ALERTNESS AT ALL TIMES WHEN THE construction activities contains chemicals known to TABLE SAW IS BEING USED. cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: WARNING! Do not allow familiarity (gaine

Dezember 2002 7:52 07 mikosoft praha s.r.o. mikosoft praha s.r.o. mikosoft praha s.r.o. mikosoft praha s.r.o. 2 • 2 610 392 415 • 02.12 3 4 5 7 8 9 10 12 13 5 14 2 11 6 15 16 1 PKS 46 1 2 3 4 18 6 7 8 9 14 5 13 12 15 16 11 17 10 PKS 40 2 610 392 415 - Buch Seite 2 Dienstag, 10. Dezember 2002 7:52 07 mikosoft praha s.r.o. mikosoft praha s.r.o. mikosoft praha s.r.o. mikosoft praha s.r.o. 3 • 2 610 392 415 • 02.12 A 21 22 8 19 20 16 15 B 24 23 25 26 2 610 392 415 - Buch Seite 3 Dienstag, 10. Dezemb

Fur ma.genauen Schnitt die Sage so ansetzen, wie in Abbildungen gezeigt. Hinweis: Am besten Probeschnitt durchfuhren. A A 2 610 392 415 - Buch Seite 4 Dienstag, 10. Dezember 2002 7:52 07 n Vor allen Arbeiten am Gerat Netzstecker ziehen. n Schutzhandschuhe tragen. n Die verwendeten Sageblatter mussen den in dieser Bedienungsanleitung angegebe- nen Kenndaten entsprechen. n Nur Sageblatter verwenden, deren zulas- sige Drehzahl mindestens so hoch ist wie die Leerlaufdrehzahl des Gerates. Zum Anziehe

1. Lower the head assembly and lock into position. 2. Loosen the six (6) kerf screws using the multi purpose tool. 3. Adjust the kerf inserts as close to the blade (teeth) as possible without touching the blade. 4. Tighten the kerf screws. NOTE: At extreme bevel angles the saw blade may slightly cut into kerf insert. 10505152025850803035757065605522.531.685Bevel Lock60555045353040Kerf Inserts Figure: Kerf Insert Depth Adjustment • When the diameter of the blade has been reduced due to sharpening

! CAUTION Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia. Accessories ! WARNING If an extension cord is RECOMMENDED SIZES OF EXTENSION CORDS necessary, a cord with 120 VOLT ALTERNATING CURRENT TOOLS adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of

Underwriters Laboratories. This symbol designates This symbol designates that this tool is listed by that this tool is listed by Underwriters Laboratories, the Canadian Standards and listed to Canadian Association. Standards by Underwriters Laboratories. -5 This symbol designates that this tool complies to NOM Mexican Standards. Model number 1590EVS & 1591EVS Voltage rating 120 V 50 - 60Hz Amperage rating 6.4 A No load speed n0 500-2,800/min Stroke length 1" Wood 5-3/8" Aluminium 3/4" Steel 3/8"