Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2. Remove the magnifier, position the pointer over 0° and replace the magnifier. Fig. T ADDITIONAL BLADE ADJUSTMENTS (FIG. S) NOTE: The adjusting lock nuts are 8 ram. The adjusting mechanism is located above the blade height adjusting hand wheel under the tabletop, tf the front and rear measurements are not the same. If the blade is partial to right aide: 1. Loosen the two lock nuts (1) and turn the left adjustment screw (2) counterclockwise, then adjust the right side adjustment screw (3) clockwise. 2. Remeasure, as described in steps 4 to 9 in the prior section. 3. When alignment is achieved, turn the left adjustment screw (2) until it touches the pivot rod (4) then tighten both lock nuts (1). if the blade is partial to left aide: 1. Loosen the two lock nuts (1) and turn the right adjustment screw (3) counterclockwise, then adjust the left side adjustment screw (2) clockwise. 2. Remeasure, as described in steps 4 to 9 in the prior section. 3. When alignment is achieved, turn the right adjustment screw (3) until it touches the pivot rod (4) then tighten both lock nuts (1). MITER GAUGE ADJUSTMENT (FIG. T=I) 1. Loosen the lock handle (1) to allow miter body (2) to rotate freely (Fig. T-1 ). Position the miter body at 90° so the positive detent secures its position. Tighten the lock handle to hold the miter body in position. 2. tf the pointer (3) requires adjustment, loosen the screw under the pointer with a hex key. Adjust the pointer to 90° on the scale then firmly tighten the adjustment screw. 3. To change angles on miter gauge, loosen the lock handle (1) and rotate the miter body to desired angle as indicated by the scale. Secure in position by tightening the lock handle. Fig. T-1 2 1 3 16 BASICSAWOPERATIONS RAISETHEBLADE (FIG. U) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. U TiLTiNG THE BLADE (FIG. U) 1. To tilt the saw blade for bevel cutting, loosen the bevel lock knob (2) and turn the tilting handwheel (3). 2. Tighten the bevel lock knob (2) to secure. ON/OFF SWITCH (FIG. V) The ON / OFF switch has a removable safety key. With the key removed from the switch, unauthorized and hazardous use by children and others is minimized and the saw will not turn on. 1. To turn the saw ON, insert key (1) into the slot in the switch (2). Move the switch upward to the ON position. 2. To turn the saw OFF, move the switch downward. 3. To lock the switch in the OFF position, grasp the sides (or yellow part) of the switch toggle (1), and pull it out. 4. With the switch key removed, the switch will not operate. 5. tf the switch key is removed while the saw is running, it can be turned OFF but cannot be restarted without re-inserting the switch key (1). Fig. V OVERLOAD PROTECTION (FIG. V) This saw has an overload relay button (3) that resets the motor after it shuts off due to overloading or low voltage, tf the motor stops during operation, turn the ON / OFF switch to the OFF position and unplug the saw. Wait about five minutes for the motor to cool. Plug in the saw, push in the reset button (3) and turn the switch to the ON position. IA WARNINGI To avoid injury, the ON / OFF switch should be in the OFF position and the plug removed from the power source while the cool down takes place, to prevent accidental starting when the reset button is pushed. Overheating may be caused by misaligned parts or a dull blade or undersized extensing cord. inspect your saw for proper setup before using it again. USING THE TABLE EXTENSION (FIG. W, X) tf the table extension is not parallel with the table, remove the bolts (1) and position the extension leveling spacers (2) between the table extension and tube until it is parallel with the table, then tighten the bolts. NOTE: See page 6 for table of loose parts ITEM: D Fig. W 1. Release the extension cam locking levers. 2. Slide the extension out until the correct measurement is displayed on the tube scale. The user sights the scale off the edge of the table. 3. Tighten all extension lock handles. Fig. X Right sidesca_e of table e.tens_on Left side scale of table extension 17 USINGTHE DUST CHUTE (FIG. Y) IA WARNING I To prevent fire hazard, clean and remove sawdust from under the saw frequently. To prevent sawdust buildup inside the saw housing, attach a vacuum hose (1) to the dust chute (2) at the rear of the table saw. Do not operate the saw with the hose in place unless the vacuum is turned on. Fig. Y CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand. Ripping requires the use of the rip fence, and crosscutting requires the miter gauge. NEVER USE THE TWO AT THE SAME TIME. [A WARNI"G I Before using the saw each and every tim...