Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
15 Wing Bolt, Lock spring Base Guide Fig. 16 (Rip Fence) . Never operate the circular saw with the saw blade turned upward or to the side. . Do not fix and secure the switch lock. Besides, keep your finger off the switch trigger when the circular saw is being carried around. Otherwise, the main body switch can be inadvertently turned ON, resulting in unexpected accidents. . Keep the light ON during cutting operation only. If it is lit ON in other cases, the main body switch can be inadvertently turned ON, resulting in unexpected accidents. English CAUTION: . Don’t remove circular saw from workpiece during a cut while the saw blade is moving. Pull out the battery after completing operation. NOTE: Take care not to lock the motor. If the motor is locked, immediately turn the power off. If the motor is locked for a while, the motor or battery may be burnt. 1. Operation of switch (switch trigger and light switch) (1) For safe operation of the machine, a Switch Lock “switch lock” is provided on the side of a (Be used as both handle. If the “switch lock” is pulled in a state where it is pressed in the direction of the arrow mark, the main switch can be turned ON. And the “switch lock” is used as the “light switch”. If the “switch lock (light switch)” is pulled in a state, the light is turned ON. (2) After the switch is turned ON, even when you release your hand from the switch lock, the saw blade continues running and the light continues being turned ON as long as you keep on pulling the switch trigger. (3) If you release the switch trigger, you can turn OFF the switch and the “switch lock” returns to the original position automatically and the light turns OFF too. NOTE: If the saw is set aside with the battery still installed, then depending on the orientation of the saw, if the “Switch Lock” comes in contact with the floor surface or wall surface, the light can remain on continuously. Please be aware that if the light is allowed to remain on continuously, even a fully charged battery can be completely discharged in about 3 hours. 2. Working performance per single charge (Reference data) . Cutting capability differs according to the condition of lumber, type of saw blade, ambient temperature, battery characteristics, etc. Switch Trigger Switch Lock and Light Switch) Fig. 17 Wood Capacity 2 . 8 (Spruce-Pine-Fir) 85 (cuts) Concreteform plywood (1/2” (12 mm) t) 148 ft (45 m) To improve working efficiency per single charge, . Minimize operation (no-load operation) other than cutting; English . Avoid any unreasonably forced pressure to the motor during cutting operation by twisting or pressing the circular saw forcibly; . Avoid any use of dull saw blade. 3. Cutting procedures CAUTION: . Recheck that the saw blade is securely clamped. . Confirm that the clamp lever for adjusting the slot depth, the wing-bolt (A) for adjusting the angle of inclination. (1) Place the saw body (base) on the lumber, and as in Fig. 18 align the intended line of cut with the saw blade, using the notch at the front of the base. This relationship of base to lumber should remain unchanged regardless of the inclination of the base. (2) Ensure that the switch is turned to the ON position before the saw blade comes in contact with the lumber. The switch is turned ON when the trigger is squeezed; and OFF when the trigger is released. (3) Moving the saw straight at a constant speed will produce optimum cutting. CAUTION: Before starting to saw, ensure that the saw blade has reached full speed revolution. . Should the saw blade be stopped or made an abnormal noise during operation, turn off the switch immediately. When finished with a job, pull out the battery from the main body. . Twisting and forcibly pressing the saw during cutting can result in unreasonable pressure on the motor, so try to go straight quietly. . In the situation where the circular saw is continuously operated while replacing the battery with stocked spare batteries one after another, the motor tends to overheat. Therefore, whenever the housing becomes hot, give the saw a break for a while. . Avoid cutting operation in a state where the base bottom is afloat from the material being cut. Otherwise, the motor can get locked. When not inclinedWhen inclined 45° Fig. 18 English MOUNTING AND DISMOUNTING THE SAW BLADE CAUTION: To avoid serious accident, ensure the switch is in the OFF position, and pull out the battery. 1. Dismounting the saw blade (1) Set the cutting volume at maximum, and place the Circular Saw as shown in Fig. 19. (2) Depress the lock lever, lock the spindle, and remove the hexagonal-flange bolt and washer(B) with the box wrench. (3) While holding the safety cover lever to keep the safety cover fully retracted into the saw cover, remove the saw blade. (Fig. 20) 2. Mounting the Saw Blade (Fig. 21) WARNING: If the bolt is worked using other tools than the provided box wrench, excessive tightening and insufficient tightening may take place, resulting in injury. . Take ...