Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
3. Rotate the mitre table (21) until the pointer aligns with the desired angle on the mitre scale (22). 4. Retighten the mitre lock (25). WARNING. Be sure to tighten the mitre lock before making a cut. Failure to do so could result in the table moving during the cut, causing serious personal injury. 5. Loosen the bevel lock (16) and pull out the 0. bevel adjuster (18) and move the saw arm (5) to the left or right to the desired bevel angle (between 0. and 45.). Tighten the bevel lock (16). 6. Place the workpiece flat on the table with one edge securely against the fence (19). If the board is warped, place the convex side against the fence. If the concave side is placed against the fence, the board could break and jam the blade. 7. When cutting long pieces of timber, support the opposite end of the timber with the side bars (37), a roller stand or a work surface that is level with the saw table. 8. Use the clamp assembly (10) to secure the workpiece wherever possible. 9. It is possible to remove the clamp assembly (10) by loosening the clamp assembly lock (11) and moving it to the other side of the table. Make sure the clamp assembly lock is tight before using the clamp. 10. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems. 11. Hold the operating handle (7) firmly and squeeze the switch trigger (24). Allow the blade to reach maximum speed. 12. Press the release latch (36) and slowly lower the blade into and through the workpiece. 13. Release the switch trigger (24) and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before removing the workpiece. Adjusting the laser lines The lower laser is factory set to emit a laser line along the right-hand side of the blade. The upper laser is factory set to emit a laser line to the left-hand side of the blade. This upper laser can be adjusted by the operator to suit blades of different kerf widths. To adjust the position of the upper laser, proceed as follows: 1. Remove the laser cover by pulling it towards you. 2. Switch on the laser lights with the on/off switch (2) (fig. w). 3. Using a Phillips head screwdriver (not supplied), adjust the position of the line from the upper laser by turning the laser pitch control (4) (fig. x). 4. Adjust until the left-hand laser line is aligned with the left-hand side of the blade. 5. Switch off the laser lights. v w x Using the laser line generator WARNINGS Do not stare directly at the laser beam. Never aim the beam at any person or an object other than the workpiece. Do not deliberately aim the beam at personnel and ensure that it is not directed towards the eye of a person for longer than 0.25s. Always ensure the laser beam is aimed at a sturdy workpiece without reflective surfaces. Wood or rough coated surfaces are acceptable. Bright shiny reflective surfaces are not suitable for laser use as the reflective surface could direct the beam back at the operator. Always remember to switch off the laser on/off switch (2) after finishing a job. Only turn the laser beam on when the workpiece is on the mitre saw table. 1. Mark the line of the cut on the workpiece. 2. Adjust the angle of mitre and bevel of the cut as required. 3. Switch on the laser light on/off switch (2). 4. Clamp the workpiece in position using the laser lines to align the blade with the pencil mark on the workpiece. NOTE. To cut to the left-hand side of the blade, align the left-hand laser line with the pencil mark. To cut to the right-hand side of the blade, align the right-hand laser line with the pencil mark. 5. Plug in the machine and start the motor. 6. Press the release latch (36). 7. When the blade is at its maximum speed (approximately 2 seconds), lower the blade through the workpiece. 8. After completing the cut, switch off the laser light on/ off switch (2). 9. After each use, clean the laser light assembly (1) as described below: • Switch off the laser light switch (2) and then remove the plug from the power point. • With the saw arm (5) in the raised position, use a soft brush to dust away the sawdust build-up around the assembly. NOTE. Wear eye protection whilst brushing the dust away. y Maintenance WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making and adjustments or maintenance procedures. Power cord maintenance If the supply cord needs replacing, the task must be carried out by the manufacturer, the manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard. Cleaning 1. Keep the tool’s air vents unclogged and clean at all times. 2. Remove dust and dirt regularly. Cleaning is best done with a soft brush or a rag. 3. Re-lubricate all moving parts at regular intervals. 4. Never use caustic agents to clean plastic parts. CAUTION. Do not use cleaning agents to clean the plastic parts of the saw. A mild detergent on a damp cloth is recommended. General ...
Dieses Handbuch ist für folgende Modelle:Kreissägen - REDEYE DB305SMS (710.76 kb)