Login:
Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Anleitung Craftsman, modell 315.22831

Hersteller: Craftsman
Dateigröße: 220.94 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


SCALE FRONTRAIL HEIGHT HANDWHEEL SQUAREHEAD RAILSLOT HEXNUT SWITCHSLOT Fig. 7 TABLETOP VIEWEDFROMABOVE TABLE SAWTABLE EXTENSION SCALE \. FRONTRAIL 7-1/8 in, MARKRIGHTSCALE Fig. 8 HEXNUT FLATWASHER Fig. 6 • Insert the two remaining pan head screws into holes in the fine adjustment knob bracket. • Attach the fine adjustment knob bracket to the bottom of the fence head on the right or the left side of the fence handle. Securely tighten the two screws. BRACKET SCREWS __ Fig. 9 MOUNTING THE SWITCH • Locate the switch assembly, The fasteners should still be attached. Note: If the fasteners were removed from the switch, see instructions in your table saw Owner's Manual for mounting the switch or refer to Figure 10. • Holding the switch to the front, insert and slide the two square nuts into the lower slot of the front rail. _I, WARNING: Place the switch out of the immediate work area to avoid accidentally turning it off during operation. • Slide the switch assembly to a convenient position, leaving ample clearance for the handwheel. Tighten securely with a screwdriver. • Attach the front rail end caps and screws with a phillips screw driver. See Figure 11. FRONTRAIL \ P TABLE EXTENSION SWITCHSCREW SWITCH ASSEMBLY Fig. 10 ENDCAP SCREW Fig. 11 ALIGNING THE RIP FENCE AND FRONT RAIL The rip fence scale indicator is installed on the right side of the rip fence but can be removed and reinstalled on the left side if needed. If a cutting operation requires placing the rip fence on the left side of the blade, and you find relocating the indicator necessary, simply unscrew and re-attach it. • Hook the back of the rip fence over the rear rail. See Figure 12. Lowper the front of the rip fence into the groove on the front rail. See Figure 13. • Slide the rip fence back and forth. It should move freely with about 1/16 in. clearance below the rip fence. If it doesn't, loosen the nuts holding the front rail and adjust the rail up or down. See Figure 6. RIPFENCE • Remove the rip fence and repeat on the other side of the blade. When the fence rides smoothly, tighten all rail hex nuts with a 12 mm wrench. • Push in the micro-adjust knob and turn it. The gear on the shaft assembly will engage the rack teeth on the rack and will move the fence assembly left or right. Push down on the rip fence handle to lock the rip • fence in place. TO INSTALL INDICATOR ON LEFT SIDE REARRAIL HOOKOVER REARRAIL HERE Fig. 12 RIP FENCEHANDLE Fig. 13 CHECKING RIP FENCE AND. BLADE ALIGNMENT The rip fence is self-aligning but should be checked before first use. _. WARNING: Failure to align the rip fence to the blade can cause jams and kickback, resulting in serious personal injury. • Slide the rip fence to the miter gauge groove, which is parallel to blade. Do not lock the rip fence. • Place a framing square against the blade, with the long end under the rip fence at the front. See Figure 14. Note the distance. • Move the square to the back and measure the length from other end of the fence. See ...

Dieses Handbuch ist für folgende Modelle:
Kreissägen - 113.29931 (220.94 kb)
Kreissägen - 113.29941 (220.94 kb)
Kreissägen - 113.29951 (220.94 kb)
Kreissägen - 315.22841 (220.94 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien