Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Black & Decker Dateigröße: 306.76 kb Dateiname: Unterrichtssprache:

Profundidad correcta: un diente debajo de la superficie de madera Switch Handle Poignee de l’interrupteur Mango del interruptor Warning: When blade starts cutting, release retraction lever immediately Avertissement : Lorsque la lame commence a decouper, relacher immediatement le ressort de rappel. Advertencia: Cuando el disco inicie el corte, suelte inmediatamente la palanca del mecanismo retractil Tighten Serrer Apriete Loosen Desserrer Afloje 9A 9B Blade Wrench Cle de reglage de la lame Llave del disco Switch lock-off lever Levier de verrouillage en position «arret» Palanca de seguro de apagado Switch trigger Interrupteur a gachette Interruptor de gatillo Assembly/Adjustment Set-Up WARNING: Always remove battery from tool before any of the following operations. Attaching and removing the Blade NOTE: The first time the blade bolt is removed from saw without a blade installed, it may be necessary to place the blade wrench on the bolt head and tap it sharply in the counter clockwise direction. Retract lower guard and assemble blade and clamp washers, as shown in Fig. 8. To prevent blade rotation while tightening the blade clamping screw, raise the lower guard and place the saw down on a piece of scrap wood as shown in Fig. 9A. The blade teeth will dig into the scrap wood and prevent rotation while you tighten the blade clamping screw. Tighten the blade clamping screw securely, using the wrench provided. Figure 9B illustrates an alternative method of loosening and tightening the blade by inserting a screwdriver through the hole in the blade to prevent it from moving. NOTE: The blade wrench is stored in the kerf plate as shown in Fig. 8. Cutting Depth Adjustment Adjust depth of cut using depth adjustment lever. See (Figs. 5 & 6) for proper setting. Tighten lever securely. Bevel Angle Adjustment Adjust bevel angle (Fig. 7) using bevel adjustment knob and bevel scale. Tighten knob securely. Kerf Plate Adjustment Adjust kerf plate (Fig. 8) to read zero when the bevel scale reads zero by loosening the kerf plate screw and sliding the plate as necessary. Align mark on kerf plate with drawn pencil line and advance blade into cut. The kerf plate has lines for zero bevel and 45 degree bevel cutting. A B Battery Cap Operating Instructions WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool. GENERAL CUTS (IMPORTANT: Read safety warnings and instructions. ) GUARD AGAINST KICKBACK With battery removed, follow all assembly, adjustment and set up instructions. Make sure lower guard operates. Select the proper blade for the material to be cut. • Measure and mark work for cutting. • Support and secure work properly (See Safety Rules and Instructions). • Use appropriate and required safety equipment (See Safety Rules). • Secure and maintain work area (See Safety Rules). • With battery inserted, make sure switch turns saw on and off. WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Fig. 3 illustrates typical hand support. Switch Saw is equipped with a switch lock-off feature to prevent unintentional running. To operate the tool, push down on the lock-off lever shown in Fig.9B from either side of the saw and hold it down as you depress the trigger switch. After you have depressed the trigger and the tool is running, release the lock-off lever. The tool will continue to run as long as the trigger is depressed. To turn the tool off, release the trigger switch. There is no provision for locking the tool on, and the switch should never be locked on by any other means. Automatic Electric Brake Your saw is equipped with an electric blade brake which stops the saw blade within 1-1/2 seconds of trigger release. This is automatic and requires no adjustment. Occasionally, under certain conditions, the brake will not function properly and won’t stop the saw in the 1-1/2 seconds as discussed above. If this condition occurs, turn the saw on and off four or five times. If the problem still persists, have the tool serviced at a Black & Decker service center or company authorized service facility. Pocket Cuttong (See Figure 10) Pocket cutting is used to cut a hole in a piece of material without cutting from the side. • Measure and mark work. • Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin at the back of the drawn rectangle. • Using the retracting lever, retract blade guard to an upward position, with the blade just clearing the material, start motor and gradually lower the saw into the material. WARNING: As blade starts cutting the material, release the retracting lever immediately. • Never tie the blade guard in a raised position. • When the shoe rests flat on the material being cut, complete the cut in forward direction. • Allow the blade to come to a complete stop before lifting saw from material. • Whe...

Herunterladen

Geben Sie zwei Ziffern: