(6.2kg) 120VAC, 50/60Hz, 840 Watts I3I/2” (34.3cm) 1/16” (2mm) 1.5 mil up to 10 mil (37 micron - 250 micron) each side WARRANTY AND RETURN POLICY Warranty: Your laminator is warranted to be free of defects in materials and workmanship for a period of one year from the date of purchase. In the event of a defect in material or workmanship, your dealer will (at his/her option) repair or replace the laminator. No other warranty is implied except as stated above. This warranty does not cover da

1 Introduction Congratulations on the purchase of your new CHAU VET lighting effect. We are confident you will enjoy many trouble free hours with this unit. To assist with the care and use of the product we have prepared this short guide. Operation This lighting effect has been designed to function on a mains power supply of either 120V~60Hz or 230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug for the corr

Power Light 2. Foam Board/Pouch Selector 3. On/Off Switch 4. Ready Light 5. Temperature Control 6. Loading Area Safety Instructions 1. Read all instructions before use. Save these instructions for later use. 2. Follow all warnings and instructions marked on the product. 3. Use the Fellowes laminator only for its intended purpose of laminating documents according to the indicated specifications. 4. Extreme caution should be taken when the appliance is used by or near children or invalids. 5. Do n

while ffrmiy puiiinq ism out the rea^ of îne ¡am:nator Ciontmue pi;* .iH'j the Mrr u.nt-i : ijfVA.nor>completely from the rotie's At ihis point you w^i iee ^ rnorr.^ni^'y lightening o* tension, to* owed r;y a si-o^g i>-:i m the opposite ejection 3 Release the reverse swuch. an^ r.jn tnt1- ia^ nator forward cntil ai* wnnk.ed filrr* exit^out t*v- rear NOTE: If film is wrapped arourvj the pultrolier!, does not extend out the rear of the larnnatof re^vicw the top iiim supply roll, and pofi the

Punching/Crimping Handle 2. Punching Area 3. Adjustable Margin Guide 4. Wire Size Selector 5. Paper Support 6. Binding Support 7. Crimping Area 8. Crimping Area Adjustor Dial 9. Waste Paper Tray 10. Crimping Area Size Indicator 5 13 7 4810 9 6 2 Assembly To assemble your WB 100 Wire Binding Machine, simply attach the Punching Handle to the right side of the machine and secure with the screw supplied. Next, attach Paper Support in Crimping Area as show in the diagram. Using the Binding Machine Pu

On\Off Switch 2. Ready Light 3. Binding Area 4. Cooling Stand 5. Binding Timer (TB 200 only) 4 1 2 3 4 5 13 Using the Binding Machine 1. Turn On\Off switch to "On" position. 2. Machine is ready to bind when Ready Light illuminates (approximately 1-2 minutes). 3. Using the table below, choose the correct thermal cover based on the total number of sheets to be bound: Thermal Cover Size # of Sheets Inches mm 1-30 1\8" 3.2 31-60 1\4" 6 61-90 3\8" 9.5 91-120 1\2" 12.5 121-150 5\8" 15.5 151-180 3\4" 2

die LED) defekt. Wenden Sie sich an Ihren Handler. " • Bei Anschluss eines eingeschalteten Netzwerkdevice an de Switch sollte die LINK/ACTIVITY LED des Ports aufleuchten. Fa nicht, verwenden Sie einen anderen Port, ein anderes Patchkabel uberprufen Sie das Gerat welches Sie anschlie.en wollen. " • Stellen Sie sicher, dass alle verwendeten Patchkabel einwan und nicht geknickt oder gebrochen sind. Manuel en francais Introduction Les switches Fast Ethernet LINDY 10/ 100 sont d’un design compact. La

Ne couvrez pas les aerations de l’element. Ne placez pas le produit pres d’une source de chaleur. Assurez- vous d’avoir une bonne ventilation. Pour utilisation interieure seulement. Temperature 0- 55°C, Humidite 10- 95% non condensee. Installation et utilisation Connectez l’alimentation sur le secteur et ensuite au switch. Connectez le switch a vos peripheriques reseaux ou sur un panneau de brassage. La fonction Auto- MDI/MDI- X detecte automatiquement les connexions de cascade ou classiques et

Sheet Supporter/Adjustable Coil Guide Selector 3. Adjustable Paper Margin Guide 4. Punching Area 5. Waste Paper Drawer 6. Binding Tray 7. Margin Depth Selector 8. Left Side Cover 9. Punching Handle Cover 1 4 8 3 7 6 2 9 5 Assembly 1. Attach the Punching Handle to the right side of the machine by firmly pressing square hole of handle onto square shaft. To operate correctly, the handle should be positioned as illustrated above. NOTE: If the handle is not positioned as illustrated it will not punch