Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Royal Sovereign Dateigröße: 479.51 kb Dateiname: Unterrichtssprache:

5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back. 6. Allow some of the film with melted resin to stick to the Guiding Paper. 7. Place the film from lower shaft beneath the film from the upper roller which is already meiting. and unwind films of both rollers 30~40cm(1~1.3ft) for loosing the tension. 8. Set the pressure lever to the 1mm. 9. Set speed at 1 and press the RUN button. The films will be fed into the machine and will come out from the rear site of machine. 10. Check the status of lamination and place the pressure lever at lamination mode. HANGING FILM TA KE UP DEVICE PAPER BACK COLD FILM UPPER IDLE BAR LOWER IDLE BAR HOT ROLLER PAPER BACK - 7 - CONTROL OF ROLLER PRESSURE ***Methods of controlling pressure of the roller** 1. For setting, pull the pressure lever out and turn the lever to following the indication 2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C) 3. 10~13mm(Board) : For laminating 10~13mm thick board 4. 5~7mm(Board) : For laminating 5~7mm thick board 5. 1mm(Hard Board) : For laminating 1mm thick board 6. Laminating : For laminating 32~250micron thick film - 8 INSTRUCTIONS FOR CONTROL PANEL We designed this machine standing by user’s convenience. You can manipulate speed and temperature . ***Terms*** 6 1 4 2 6 2 1 33 5 - 9 1. FUNCTIONS OF CONTROL PANEL RUN/STOP BUTTON : Run or stop the rollers SPEED BUTTON : Increase or decrease speed LED OF SPEED : Display or speed LED OF TEMP. : Display temperature TEMP.BUTTON : Increase or decrease temperature REVERSE BUTTON : To make the rollers run backward 2.HOW TO USE BUTTONS Push the button in order to run rollers and push button to stop it. SPEED BUTTON Push the SPEED button to increase the speed,push the speed button to decrease the speed. TEMP. BUTTON Push the TEMP. button to increase the temperature,push the TEMP. button to decrease. REVERSE BUTTON Stay pressing REVERSE button to have . The roller run backward. RUN / STOP BUTTON 1 2 3 4 5 6 1 2 5 6 RUN REV STOP - 10 - 1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. 4. After pressing the RUN/STOP button choose and set proper speed by using the SPEED button or . 5. Turn on the take up device and set the proper film tension by pressing the RUN/STOP button. Lower tension would make better operation. 10. Set pressure lever at the Hard board/15mm mode. 11. Turn off the power switch. 1. Set up the protection paper. Otherwise, glue form the film will be stuck on the face of roller and it can be seriously damaged. 2. Turn the switch RUN/STOP and “Take up motor” at the same time. *** Reference *** LAMINATING STEPS - 11 - METHOD FOR USING CUTTER **Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination. 3. Grasp film with one hand and press the cutter, cutter downward and slide it to the direction intending to cut with another hand. 4.Press the cutter and slide it the other way. - 12 IMPORTANT SAFETY CONCERNS 1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while operation. 2.Prevent children from accessing the machine Extreme Heat Will Cause Injury 3.Place the machines on the plated place in order to prevent the machine from damage. 4.Make certain that the machine is connecterd to an adequate power souce. 5.Do not use any other purposes other than Lamination. MAINTENANCE 1.Do not allow the machine to run with only one roll of film installed. The melted resin will adhere to one roller and ruin future laminations. 2.The width of film should be bigger than the material, and Width of upper side and lower side of film should be same in order not to allow melted resin to adhere to the rollers. 3.Be sure to adjust the film tension while in operation. If the tension is too tight, it could cause the film to stretch. 4.After work, you should clean the resin from the rollers before beginning the next operation 5.Please check the lubricant after long operation or you do not use for a long time. 6.Check the chain linking each gear is not loosened.The limit tension allowed is 3mm. - 13 It's not out of order SymptomCause CHECK POINT *Rollers do not operate after press RUN button 1. Power cord may not be plugged in. 2. Power switch is at OFF mode. 3. Emergency switch may be at 4. The safety cover is opened. ON mode. 1. Check the power cord. 2. Check if the switch is on. 3. Check if the emergency switch is off. 4. Check the s/w of safety cover is right. *Wrinkled lamination result 1. Film tension is not proper, too tight. 1. Adjust film tension. ASSEMBLY PARTS PART NAME EA MODEL PART NAME EA MODEL Core(76mm) 10 Bolt(M8X12) 6 RSC-1650H RS...

Herunterladen

Geben Sie zwei Ziffern: