Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 3. THE CONNECTOR PLATE IS NOT REQUIRED FOR THIS ASSEMBLY PLEASE DISCARD. 4. Assemble the ADJUSTMENT TUBE ASSEMBLY to the SEAT SUPPORT and BASE as shown on drawing, using two (2) 1/2 X 3-1/2 IN. BOLTS, four (4) 1/2 IN. WASHERS, and two (2) 1/2 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 5. Insert one (1)2 IN. SQ. END CAP into the front end of the FOOT BRACE ASSEMBLY. 6. Attach four (4) 2-1/2 X 5-1/2 IN. NON SKID STRIPS to the FOOT BRACE ASSEMBLY as shown on drawing. 7. Slide the FOOT BRACE ASSEMBLY over the ADJUSTMENT TUBE ASSEMBLY to the desired hole setting and hold in place with on SAFETY LOCK PIN. 5 049 / 849 LOW ROW ATTACHMENT ASSEMBLY INSTRUCTIONS BODYSMITH BENCH WTDE and NARROW 1. Insert one (1) 1 -3/4 IN. SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 2. Assemble the ADJUSTMENT TUBE ASSEMBLY and the CONNECTOR PLATE to the FRONT LEG of the BENCH as shown on drawing, using two (2) 3/8 X 3-1/2 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 3. Insert one (1) 2 IN. SQ. END CAP into the front end of the FOOT BRACE ASSEMBLY. 4. Attach four (4) 2-1 /2 X 5-1 /2 IN. NON SKID STRIPS to the FOOT BRACE ASSEMBLY as shown on drawing. 5. Slide the FOOT BRACE ASSEMBLY over the ADJUSTMENT TUBE ASSEMBLY to the desired hole setting and hold in place with on SAFETY LOCK PIN. MUI/TI-ANGLE BENCH 1. Remove the hardware from the assembly of the FRONT LEG to the BENCH, and discard. 2. Insert one (1) 1-3/4 IN. SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 3. Assemble the ADJUSTMENT TUBE ASSEMBLY and the CONNECTOR PLATE to the BENCH as shown on drawing, using two (2) 3/8 X 3-1/2 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 4. Insert one (1)2 IN. SQ. END CAP into the front end of the FOOT BRACE ASSEMBLY. 5. Attach four (4) 2-1/2 X 5-1/2 IN. NON SKID STRIPS to the FOOT BRACE ASSEMBLY as shown on drawing. 6. Slide the FOOT BRACE ASSEMBLY over the ADJUSTMENT TUBE ASSEMBLY to the desired hole setting and hold in place with on SAFETY LOCK PIN. 4 049 / 849 LOW ROW ATTACHMENT ASSEMBLY INSTRUCTIONS IMPORTANT: THE LOW ROW ATTACHMENT WAS DESIGNED TO BE USED ON SEVERAL PARABODY PRODUCTS. PLEASE FOLLOW THE INSTRUCTIONS INTENDED FOR YOUR SPECIFIC PRODUCT: • FLAT/INCLINE/DECLINE BENCH • FLAT and INCLINE BENCH • BODYSMITH BENCH WIDE and NARROW • MULTI-ANGLE BENCH • DELUXE LAT MACHINE • ECONO LAT MACHINE (010) FLAT/INCLINE/DECLINE BENCH: 1. Remove the hardware from the assembly of the FRONT LEG to the BENCH, and discard. 2. Insert one (1) 1-3/4 IN. SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 3. Assemble the ADJUSTMENT TUBE ASSEMBLY and the CONNECTOR PLATE to the BENCH as shown on drawing, using two (2) 3/8 X 3-1/2 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 4. Insert one (1)2 IN. SQ. END CAP into the front end of the FOOT BRACE ASSEMBLY. 5. Attach four (4) 2-1/2 X 5-1/2 IN. NON SKID STRIPS to the FOOT BRACE ASSEMBLY as shown on drawing. 6. Slide the FOOT BRACE ASSEMBLY over the ADJUSTMENT TUBE ASSEMBLY to the desired hole setting and hold in place with the SAFETY LOCK PIN. FLAT and INCLINE BENCH 1. Remove the hardware from the assembly of the FRONT LEG to the BENCH, and discard. 2. Insert one (1) 1-3/4 IN. SQ. END CAP into the front end of the ADJUSTMENT TUBE ASSEMBLY. 3. Assemble the ADJUSTMENT TUBE ASSEMBLY and the CONNECTOR PLATE to the BENCH as shown on drawing, using two (2) 3/8 X 3-1/2 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. NYLOCK NUTS. (NOTE: THE BRACKET ON THE ADJUSTMENT TUBE ASSEMBLY IS FLUSH TO THE TOP OF THE TUBE, PLEASE ASSEMBLE FLUSH SIDE UP) 4. Insert one (1)2 IN. SQ. END CAP into the front end of the FOOT BRACE ASSEMBLY. 5. Attach, four (4) 2-1/2 X 5-1/2 IN. NON SKID STRIPS to the FOOT BRACE ASSEMBLY as shown on drawing. 6. Slide the FOOT BRACE ASSEMBLY over the ADJUSTMENT TUBE ASSEMBLY to the desired hole setting and hold in place with on SAFETY LOCK PIN. 3 DASH NO DESCRIPTION 01 AS SHOWN 3/8 X 3-1/2 IN BOLT (2) 3/8 IN WASHER (2) CONNECTOR PLATE FLAT INCLINE DECLINE BENCH AND FLAT INCLINE BENCH REVISIC ~NS REV DESCRIPTION CHG NO APP’D DATE A NEW RELEASE 2337 DMT 3/94 B ADDED 049101 m PMT s. > ADJUSTMENT TUBE ASSEMBLY 1-3/4 IN SQ END CAP SERIAL NUMBER 1/2 IN WASHER (2) 1/2 IN LOCK NUT (2) 3/8 IN WASHER (2) 3/8 IN LOCK NUT (2) SAFETY LOCK PIN -2-1/2 X 5-1/2 NONSKID STRIP (4) FOOT BRACE ASSEMBLY ■2 IN SQ END CAP BODYSMITH BENCH 3/...