Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Royal Sovereign Dateigröße: 708.46 kb Dateiname: Unterrichtssprache:

-ROLLER V-LOWER IDLE BAR LOWER IDLE BAR 1. Follow the steps in the “Loading Film” procedure by loading the upper shaft with pressure sensitive film, e.g. (Royal Print-Pro Film) and lower shaft with pressure sensitive mounting adhesive films, e.g. (Royal Sovereign White-Mount or Clear-Mount). 2. Pull the upper laminate under the upper idle bar and separate the release liner from the laminate. 3. Tape the release liner to the Take-Up Paper Core and allow the laminate to hang over the main rollers. 4. Pull up the mounting adhesive and tack it to the laminate hanging over the rollers (do not use the Lower Idle Bar). 5. Reinstall the Front Table and the Paper Guide and close the Safety Cover. 6. Turn on the upper take-up motor. 7. Adjust the nip setting to 1/8"(3mm). 8. Insert and push the leader board until board reaches the nip point. 9. Press the Run button and adjust the supply roll tension knobs by rotating clockwise or counterclockwise. Turn it until the supply roll films have some resistance (the tension varies depending on the thickness of a film; the thicker the film the more tension is required). 10. Press Stop button when the leader board has completely exited the rear of the unit. 11. Use the Cross Cutter to cut the leader board from the web (see page 9). 12. Set the roller nip setting to the appropriate position for the lamination application. 14 Sovereign 13.3 Mounting 1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner (Approximately 1 in or 25mm, Figure 1). 2. With the image facing up, align the image onto the board. Press firmly from the center out (Figure 2). Figure 1 3. Adjust the pressure lever to ensure the proper opening (Figure 3). 4. Flip the image over the upper roller and hold on to the release liner (Figure 4). 5. Depress the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip (Figure 5). Depress the foot pedal once again when the board has completely exited from the rear of the unit. Trim the board if necessary. 15 RSS, RSR, RSH Series 14. INSTALLATION OF FRONT FEEDER and REAR REWINDER OPTIONS Figure 7 »■ Figure NOTE: Below options are to be installed bv an authorized RS reseller.iThese options are available for the RSH-1650.1 Installation of the Front Feeder Option (Includes 2 brackets, one spindle, and mounting hardware). 1. Install the Front Feeder to the inside of the front frames using four 1/4" (M6) hexagon bolts on each side (Figure 1) Installing the Rear Rewinder Option (Includes motorized winder, bracket, one spindle, and mounting hardware). 1. Remove the left and right covers by using a screwdriver (four screws on each side cover) (Figure 2 & 3). 2. Remove the lever knob screw and lever (Figure 4). Figure 1 Figure 2 Figure 3 3. Remove the rear cover by removing all 10 screws (4 top, 4 bottom, and 1 on each side) (Figure 5 & 6). Figure 4 Figure 5 Disassemble the power switch bracket and place the left rewinder outside of the frame; fasten with round head 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 7). Install the right rewinder on the outside of the frame and connect the motor wire connector to the rear wire (Figure 8 & 9). Reinstall the rear cover. Reinstall the side covers. Reinstall the lever knob and screw. 4. 5. 6. 7. 8. 16 ¿RSüæUn 15. MAINTENANCE Cleaning the Body...

Herunterladen

Geben Sie zwei Ziffern: