Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Black & Decker
Dateigröße: 4.38 mb
Dateiname: CG800C1178.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
If your cabinet is flat, follow STANDARD INSTALLATION; if the cabinet has a lip, refer to SPACER MOUNTING INSTALLATION. STANDARD INSTALLATION (FLAT CABINET) Important: Always wear protective glasses or goggles to prevent injury when drilling. 1. Clear countertop under installation area to avoid getting dust or debris on other appliances or items. Open cabinets and remove contents to make mounting easier. B C 4 2. With cabinet doors open, place mounting template flush against the surface of the underside of your cabinet, making sure to align thick line on template with bottom front edge of your cabinet (D). Important: Do not align screw holes on template with the partition between cabinets, as this will prevent you from installing the appliance properly. Pay close attention to where the drill holes will be set so as not to damage your cabinets during mounting. Drilling through your cabinet’s partition may cause damage to cabinets and prevent proper installation. 3. Once thick line is straight with bottom front edge, pull template tight and tape down on all 4 corners to hold in place. 4. Drilling from under the cabinet up, drill holes through the 4 places marked on the template, using a .-inch drill bit (E). Important: Always ensure you are drilling straight up through the marked mounting hole on the template. Drilling at an angle may prevent proper installation and may damage cabinets if the drill bit pierces the partition. 5. Once holes are drilled, remove tape and mounting template and save template with your instructions in case you move or wish to remount at a later time. 6. Wipe dust and debris off inside cabinet surface. Also, make sure under side of cabinet is clean. 7. Place a washer inside the cabinet over each of the 4 holes you drilled. 8. Hold appliance in place, aligning front of unit with front edge of cabinet; drilled holes on cabinet should be aligned with mounting holes on the unit. 9. Screwing from inside the cabinet down into appliance holes, tighten 4 screws in place to secure appliance to cabinet. Note: Always tighten screws to ensure the appliance does not move or shake during operation. 10. Pull out cord from cord storage behind appliance and plug into standard electrical outlet. Extra cord can be fed back into storage or hung over cord management hook behind unit (F). Note: If you are connecting this appliance to the receptacle of another †SpaceMaker appliance such as the toaster oven or coffeemaker, make sure you can easily unplug the appliance following use. 11. Your †SpaceMaker™ appliance is now ready for use! SPACER MOUNTING INSTALLATION (OVERHANG LIP CABINETS) Important: Always wear protective glasses or goggles to prevent injury when drilling. Note: Spacers are provided in case your cabinet has an overhang lip at the front edge. The spacers are used on the rear screw holes of the appliance to ensure it is level with the front. Only use spacers if your cabinet has an overhang. 1. Clear countertop under installation area to avoid getting dust or debris on other appliances or items. Open cabinets and remove contents to make mounting easier. 2. Using a ruler, measure the thickness of the overhang lip from the front to back of the overhang, accurately noting the number for use in the following step (G). Note: If you do not have a ruler, you may cut out and use the paper ruler provided on the edge of your mounting template. 3. Once you have the overhang thickness, look at the dashed lines on the mounting template; each line has a measurement next to it that indicates the height of the lip used with that line. For example, if your cabinet has an overhang thickness of .”, you will use the .” dashed line on the template. D E 5 F G 6 4. With cabinet doors open, place line selected on mounting template even with the bottom front edge of your cabinet, and tape in place against the lip (H). 5. With the paper securely taped in place against the lip, fold the rest of the mounting template back against the underside of cabinet surface, bending it to remain flush against both the back of the lip and the underside of the cabinet (J). Important: Do not align screw holes on template with the partition between cabinets, as this will prevent you from installing the appliance properly. Pay close attention to where the drill holes will be set so as not to damage your cabinets during mounting. Drilling through your cabinet’s partition may cause damage to cabinets and prevent proper installation. 6. Drilling from under the cabinet up, drill holes through the 4 places marked on the template using a .-inch drill bit (see illustration E). Important: Always ensure you are drilling straight up through the marked mounting hole on the template. Drilling at an angle may prevent proper installation and may damage cabinets if the drill bit pierces the partition. 7. Once holes are drilled, remove tape and mounting template and save template with your instructions in case you move or wish to remount at a later time....