Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Fujitsu Dateigröße: 1.94 mb Dateiname: zoneline_data_manual_08.pdf Unterrichtssprache:

Units with single rating are 265-volt units. ge.com Power Connection Kits 230/208-Volt Line Cord Connection Units 230/208-Volt Sub-Base and Direct Connected Units Electric Line Cord Heat Kit BTUH RAK 15 8600/7100 RAK 20 11700/9600 RAK 0 17100/1 900 Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) 2550/2090 11.6/10.6 15 450/2820 15.5/14.1 20 5000/4090 22. /20. 0 Electric Heat Amps include electric heater and fan motor current draw. Each Line Cord Kit has an integral Leakage Current Detection and Interruption (LCDI) or Arc Fault Current Interrupter (AFCI) device as required by National Electrical Code (NEC) and Underwriters Laboratories (UL) for units manufactured after August 1, 2004. 265-Volt Sub-Base and Direct Connected Units Power Sub-Base Connection Kit RAK204E15 RAK5172 RAK204E20 RAK5202 RAK204E 0 RAK5 02 Direct Sub-Base Connection Kit RAK204D15P RAK4157 RAK204D20P RAK4207 RAK204D 0P RAK4 07 Electric Heat BTUH Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) 8600/7100 2550/2090 11.6/10.6 15 11700/9600 450/2820 15.5/14.1 20 170100/1 900 5000/4090 22. /20. 0 Electric Heat Amps include electric heater and fan motor current draw. Units connected through sub-base do not require a LCDI or AFCI device since they are not considered to be line-cord connected. Each 2 0/208-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis, wiring to connect sub-base to building wiring and a short line cord with 9-pin connector to connect to chassis and plug into receptacle in sub-base. Short sub-base line cord may not be used without sub-base. Junction box for 2 0/208-volt chassis must be purchased separately. RAK4002A for 2900 and 900 series units RAK4002B for 5800 series units. Direct Connection Kit Electric Heat BTUH Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) RAK5157 8600 2550 9.6 15 RAK5207 11700 450 1 .0 20 RAK5 07 17000 5000 18.9 0 Electric Heat Amps include electric heater and fan motor current draw. 265-volt units are to be permanently connected in compliance with National Electrical Code and local codes and have a factory-installed junction box on the chassis. Each 265-volt sub-base kit consists of sub-base with appropriate receptacle for minimum circuit amperage, chaseway to route power connector from sub-base to chassis and wiring to connect sub-base to building wiring. 265-Volt Power Connection Kit must be ordered separately. Important Essential Elements Ordering Overview 2 0/208-volt line cord connected units — order line cord kit 2 0/208-volt sub-base connected units — order sub-base and junction box 265-volt units — order sub-base and power connection kit Zoneline® Chassis Nomenclature The Zoneline chassis is identified by a model number defining the type of unit, cooling capacity, electrical information and optional features included on the unit. When specifying or ordering the Zoneline chassis, the use of this nomenclature will assure receiving the correct unit. EXAMPLE Zoneline packaged terminal chassis A Z 5 8 H 1 2 D A D Chassis series 29=deluxe line cool/ electric heat 9=deluxe line heat pump 58=premium line heat pump Unit type E=cooling with electric resistance heat H=heat pump with electric resistance heat Nominal cooling capacity 07=7,000 BTUH cooling 09=9,000 BTUH cooling 12=12,000 BTUH cooling 15=15,000 BTUH cooling Special Features B=base unit C=corrosion treated D=internal condensate removal (ICR) system (heat pump models only) (not for coastal areas) P=Dry Air 25 (2800 Series only) Voltage/Phase/ Frequency D=2 0/208-Volt, single-phase, 60 Hz E=265-Volt, single-phase, 60 Hz Universal power connection The Zoneline® 2900, 900 and 5800 Series have incorporated changes suggested by customers, along with — No Mechanical Parts — No Special Maintenance Required • Helps Maintain Lower Relative Humidity In Rooms • Maintains Comfort at Slightly Higher Room Temperatures — Reduces Operating Costs — Provides Comfort Without Overcooling • Corrosion Treatment is Standard • Excellent Choice for Humid Climates • Available in 7000, 9000 and 12000 BTU Sizes The Dry Air 25 system, a heat pipe, is a hermetically sealed heat transfer surface installed in a “saddlebag” configuration around the indoor (evaporator) coil of the Zoneline. This coil arrangement will transfer heat from the front coil of the saddlebag to the rear coil without power consumption. This assembly uses R-22 as the refrigerant and is not connected to the regular Zoneline refrigerant circuit. As warm, humid air is pulled through the pre-cool (front) section of the heat pipe, the heat removed from the air is absorbed by the refrigerant, causing the refrigerant to change to a gas and flow to the re-heat (rear) section of the heat pipe. The air leaving the pre-cool section of the heat pipe is cooler and at a higher relative humidity level than the room air. The pre-cooled air is f...

Herunterladen

Geben Sie zwei Ziffern: