Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Haier Dateigröße: 745.11 kb Dateiname: 3e390d9b-151a-4d66-a611-30bdb85a23ac.pdf Unterrichtssprache:

(b) Seaside with high salt content in the air. (c) Near to hot spring with high content of sulfide gases. (d) Area with frequent fluctuation of voltage e.g. factory, etc. (e) In vehicles or ships. (f) Kitchen with heavy oil vapour or humidity. (g) Near to the machine emitting electric-magnetic waves. (h) Places with acid, alkali vapuor. TV, radio, acoustic appliances etc are at least 1 m far away to the indoor unit, outdoor unit, power supply wire, connecting wire, pipes, otherwise images may be disturbed or noises be created. Connect earthing wire. Earthing wire should not be connected to the gas pipe, water pipe, lightning rod or phone line, incorrect earthing may cause shock. Earthing Use discharge pipe correctly to ensure efficient discharge. Incorrect pipe use may cause water leaking. As required, take measures against heavy snow. [Wiring] Air-conditioner should be equipped with special power supply wire. [Operating noise] Chose the following locations: (a) Capable of supporting air-conditioner weight, don't increase operating noise and vibration. (b) Hot vapour from outdoor unit outlet and operating noise don't disturb neighbour. No obstacles around the outdoor unit outlet. 5 Introduction to Spare Parts (For series 14 18 ) Swing louver (Air flow direction can be adjusted by using the SWING button on the remote controller) Electrical Components Case Air Inlet Grille Air Filter (Inside of the Inlet Grille) (For series 24 28 36 42 52 ) Drain Hose Swing fender Refrigerant pipeCable line Earthing line Air filter Outlet Suction grill (located in the suction grill) In cooling operation, to discharge the water from inside the room. Discharge unit (built in) (located in the outlet) Note : For the wired control type unit, the unit state should be checked by the the wired controller, instead of the remote receiver; and if you set the TIMER function, the TIMER LED on the remote receiver will not be on. 6 Maintenance Clean the unit Turn off the power supply switch Do not touch with wet hand. Do not use hot water or volatile liquid ON OFF The 4 fixed bolts must be loosed as shown in the figure by arrow if they are bolts, the method is that: push the blots inward till to another edge. Generally the fixed blots are opened for inlet grille easily up and down as well cheaning the air filter.After open it,lower the inlet grille using remote controller, the maximum distance is 2.24m. Then turn the 1 rotated clamps 90 degree as shown in the figure, hold the air filter and nearly in the horizontal direction slightly pull it out. Clean the air filter Clean the air filter with water or vacuum cleaner. Use the detergent or neutral soapy water if the air filter is too dirty. Then rinse the air filter with water,and reinstall after drying. Caution: Do not clean the air filter with hot water over 40 C, otherwise may damage the filter. Sweep the filter carefully. Clean indoor (outdoor )unit Clean with hot wet cloth and neutral detergent, then wipe with dry cloth.Do not use too hot water (over 40 C) which may result in fading and deforming. Do not use insecticide and chemical washing agent. Fixing nolt Fixing nolt Fixing nolt Rotary fixing clamp Outward drawable filter For detailed information consult dealer. NOTE: 7 Maintenance (For series 24 28 ) 3. Dismantle air filter CAUTION! 4. Clean 6. Close inlet grill 7. Press the filter signal return key on the controller. (A) Remove dust with vacuum filter. 5. Install air filter (1) Put filter into protruding parts at the top of the inlet grill. (2) Connect the two pothooks with inlet grill See 2 [Clean inlet grill] 1. Open inlet grill See 1. Connet the two pothooks with inlet grill PUSH Press the elliptical knob the inlet grill will automatically drop Open two pothooks Pothook Press the elliptical "PUSH" knob, the inlet grill will automatically drop. (the inlet grill is catched with two pothooks) Drag the knob of the grill back lift the filter and take down. Air filter '' '' [Clean air filter] NOTE 1. Open inlet grill Press the elliptical "PUSH" knob, the inlet grill will automatically drop. (the inlet grill is catched with two pothooks) When having to clean, don't dismantle air-filter,otherwise may cause faults. In the environment where there is too much dust, air filter should be cleaned for more times. (about half a year one time) 2. Open two othooks (B) Wash with water. With too much dust, use soft brush and neutral detergent. Swing off the water, and then place in cool place. PUSH Press the elliptical knob the inlet grill will automatically drop Open two pothooks Pothook 8 Maintenance 3. Take of inlet grill 4. Clean CAUTION! NOTE When the filter too much dust To spray the special detergent for vent fan or utensils. 5. Install inlet grill 6. Install air filter 7. Close inlet grill [Clean outlet and shell] see 3 see "Clean air filter" see 1 CAUTION! Don't use gasoline, benzene, dilutant, polishing powder, or liquid inseticide. [Dismantle and install swing plate ] 1. Fix the swing pl...

Herunterladen

Geben Sie zwei Ziffern: