Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Maytag Dateigröße: 3.26 mb Dateiname: HQ2244UH.pdf Unterrichtssprache:

Do not operate switches with wet hands. • It may cause an electric shock. Do not apply an insecticide or flammable spray. • It may cause a fire or deformation of the cabinet. Do not put a heater, etc. where it is exposed to direct air flow. • It may cause imperfect combustion. 5 About the Controls on the Air Conditioner 2 6 1 8 4 3 7 OPERATION TEMP TIMER AIR SWING MODE ECONOMY FAN SPEED 1 6 2 4 5 3 7 About the Controls on the Air Conditioner Controls OPERATION BUTTON • To turn the air conditioner ON, push the button. To turn the air conditioner OFF, push the button again. • This button takes priority over any other buttons. • When you first turn it on, the air conditioner is on the High cool mode and the temp. at 72°F(22°C) OPERATION MODE SELECTION BUTTON Every time you push this button. It will toggle between COOL, ECONOMY, FAN and DRY. ROOM TEMPERATURE SETTING BUTTON This button can automatically control the temperature of the room. The temperature can be set within a range of 60°F to 86°F by 1°F. (16°C to 30°C by 1°C) Select the lower number for lower temperature of the room. FAN SPEED SELECTION BUTTONS Every time you push this button, it is set as follows. {High(F3) Low(F1) Med(F2) High(F3)...}. ECONOMY • If you push the button, the fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed. ON/OFF TIMER BUTTON You can set the time when the unit will turn on or turn off automatically by pressing the timer button. If the unit is operating, this button controls the time it will be turned off. If the unit is in off state, this button controls the time it will start. Every time you push this button, the remaining time will be set as follows. - STOPPING OPERATION • Every time you push this button, when the air conditioner is operating, timer is set as follows. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours 0Hour 1Hour 2Hours ...) • The Setting Temperature will be raised by 2°F(1°C) 30min. later and by 2°F(1°C) after another 30 min. - STARTING OPERATION • Every time you push this button, when the air conditioner is not operating, timer is set as follows. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours 0Hour 1Hour 2Hours ...) AIR SWING BUTTON This button can automatically control the air flow direction. REMOTE CONTROL SIGNAL RECEIVER DRY • When this unit is in dry mode, the fan rotates in low speed. The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and the unit checks the room air temperature to set itself. 7 6 8 9 Precaution: The Remote Controller will not function properly if strong light strikes the sensor window of the air conditioner or if there are obstacles between the Remote Control unit and the air conditioner. Additional controls and important information. Ventilation The ventilation lever must be in the CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is drawn out. Air Direction The vertical air direction is adjusted by rotating the horizontal louver forward or backward manually. The horizontal air direction is adjusted by rotating the vertical louver right or left by Remote Controller. The direction of air can be controlled wherever you want to cool by adjusting the horizontal louver and the vertical louver. • VERTICAL AIR-DIRECTION CONTROL • HORIZONTAL AIR-DIRECTION CONTROL How to Secure the Drain Pipe In humid weather, excess water may cause the BASE PAN to overflow. To drain the water, remove the DRAIN CAP and secure the DRAIN PIPE to the rear hole of the BASE PAN. Press the drain pipe into the hole by pushing down and away from the fins to avoid injury. (See Fig.1) Optional(CW3H02502C) 1. Remove the rubber plug and slide the chassis out from the cabinet. (See Fig.2) 2. Install the drain pan over the corner of the cabinet where you removed the plug with 4 screws. (See Fig.3) 3. Connect the drain hose to the outlet located at the bottom of the drain pan. You can purchase the drain hose or tubing locally to satisfy your particular needs. (Drain hose is not supplied). (See Fig.3) 4. Selec...

Herunterladen

Geben Sie zwei Ziffern: