Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Dimplex Dateigröße: 202.64 kb Dateiname: Unterrichtssprache:

Supply wire must be of two wire plus ground variety, with a rating capable of handling all heaters on the circuit. Supply wire should be rated for a minimum of 60C. Make electrical connection according to relevant diagrams shown on Figure # 2. Make connections using approved wire nut connectors and secure the grounding wire to the green ground screw on the heater chassis. On models with Register Style Front Grills only, a terminal box cover plate is provided. Insert the tabs of the cover plate into the slots and secure the other side of plate with the screws provided. STEP 5 – Secure the Front Panel If your unit has a built in thermostat remove the plug on the front panel. Fasten the Front Grill using the screws provided. It is important to note that the front grill is oriented in the required positions shown in Figure # 1 and on the Multi – Directional grille, the larger louvered portion is placed over the fan blade portion of the heater. For units with built in thermostat push knob onto thermostat shaft through plug hole. Operation And Maintenance For units with built in thermostats, rotate the thermostat knob fully clockwise. Heater should activate. When the room reaches the desired temperature, slowly rotate the knob counterclockwise until unit shuts off. The heater will automatically cycle around this preset temperature setting. All units contain an Automatic Reset High Temperature Cutout, which will shut the heater off in the event of abnormally high operating temperatures. In addition a Red Warning Light will activate providing a visual warning. If this condition exists, disconnect all power to the unit and call a licensed electrician for service. Do not use heater until the problem is determined and corrected. ENSURE POWER TO THE UNIT IS DISCONNECTED PRIOR TO SERVICING OR PERFORMING CLEANING MULTI-DIRECTIONAL GRILLE ORIENTATION FOR USE WITH 610070000/6100790000 WH SERIES HEATERS ALTERNATE MULTI-DIRECTIONAL GRILLE ORIENTATION REGISTER GRILLE WIRING ACCESS ORIENTATION NOTE: MAINTAIN A MINIMUM CLEARANCE OF 8” FROM ADJACENT WALLS, FLOORS AND CEILINGS ON ALL FOUR SIDES OF THE GRILLE RECESS BOX FIGURE #1 1-800-668-6663 In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice. 7204220100 REV.06 RWH & WH MODELS WIRING DIAGRAM DWH MODELS (DOUBLE ELEMENT) WIRING DIAGRAM REPLACEMENT PARTS Part # REPLACEMENT PARTS Part # Grilles Elements ( Single Element Style ) Multi - Directional Grille - Almond WH 120V 500W 2200110001 Multi - Directional Grille - White WHW 120V 750W 2200110002 Register Grille - Almond WHREG 120V 1000W 2200110003 Register Grille - White WHREGW 120V 1500W 2200110004 Motors 500/375W 2200110007 120 volt models 2000060003 240/208V 750/500W 2200110008 240/ 208v models 2000060001 240/208V 1000/750W 2200110009 Fan Blade 00010026 240/208V 1500/1125W 2200110010 High Limit Cutout 00009201 240/208V 2000/1500W 2200110011 Recess Mount Box WHWC Elements ( Double Element Style ) ACCESSORIES 240/208V 2000/1500W 2200120009 WHAT1A _ Single Pole Thermostat Kit WHASBA Surface Mount Box - Almond 240/208V 1000/750W 2200120008 WHAT2A _ Double Pole Thermostat Kit WHASBW Surface Mount Box - White *NOTE: For reduced heat output do not connect wire C to 240 volt line (L2). Wire C must be capped off using a wire nut supplied by the customer when not used. Cat. No. Volts Wattage Connections DWH2010 or DWHREG2010 240 2000W L1-A, L2-B & C 1000W L1-A, L2-B ONLY* DWH1507 or DWHREG1507 240 1500W L1-A, L2-B & C 750W L1-A, L2-B ONLY* * - Disconnect and cap off wire "C" using wire nuts supplied by customer. WARNING - Hazard of severe shock. CAUTION- Disconnect all power coming to heater at main service panel before wiring or servicing. RECESS BOX OPTIONAL SURFACE BOX TERMINAL BOX COVER (Required for register grille only) HEATER ASSEMBLY REGISTER GRILLE MULTI-DIRECTIONAL GRILLE ...

Herunterladen

Geben Sie zwei Ziffern: