Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Panasonic Dateigröße: 850.51 kb Dateiname: CSC9BKP.PDF Unterrichtssprache:

• Signal received sound. One short beep or one long beep. Notes for Remote Control. • Do not throw or drop. • Do not get it wet. • Certain type of fluorescent lamps may affect signal reception. Consult your dealer. CHECK TEMP AUTO ON OFF AUTO DRY FAN F COOLCOOL FAN AUTO RESET CLOCK MODE SLEEPECONOMY FAN SPEED AIR SWING OFF CANCEL ON SET 1 2 3 TIMER OFF/ONPOWERFUL AUTO MANUAL #! $% ^ $ * & 358 7 9 0 64( 21 How to Insert the 1 Slide down the remote control cover completely 2 Insert the batteries – Be sure the direction is correct – 12.00 at display - flashing • Set the current time (CLOCK) immediately to prevent battery exhaustion. About the batteries • Can be used for approximately one year. Observe the following when replacing the batteries • Replace with new batteries of the same type. • Do not use rechargeable batteries (Ni-Cd). • Remove the batteries if the unit is not going to be used for a long period. 1Signal Transmitter 2Operation Display 3Powerful Mode Operation Button 4Room Temperature Setting Button (self-illuminating button) 5Operation Mode Selection Button 6Economy Mode Operation Button 7Auto Airflow Direction Button 8ON-Timer Button 9OFF-Timer Button 0 Reset Point (Press with fine-tipped object to clear the memory) ! OFF/ON Button (self-illuminating button) @ Sleep Mode Operation Button # Fan Speed Selection Button $ Manual Airflow Direction Selection Button % Timer Set Button ^ Timer Cancellation Button & Time-Setting Button * Clock Button ( Remote Control Cover RESETCLOCK OFF CANCEL 1 2 3TIMER ON SET 2 1 1.5V1.5V 4 ENGLISHNAME OF PART Remote Control Remote Control Signal. • Make sure it is not obstructed. • Maximum distance : 10 m (32.8 ft.). • Signal received sound. One short beep or one long beep. Notes for Remote Control. • Do not throw or drop. • Do not get it wet. • Certain type of fluorescent lamps may affect signal reception. Consult your dealer. CHECK TEMP AUTO ON OFF AUTO DRY FAN F COOLCOOL FAN AUTO RESET CLOCK MODE SLEEPECONOMY FAN SPEED AIR SWING OFF CANCEL ON SET 1 2 3 TIMER OFF/ONPOWERFUL AUTO MANUAL #! $% ^ $ * & 358 7 9 0 64( 21 How to Insert the 1 Slide down the remote control cover completely 2 Insert the batteries – Be sure the direction is correct – 12.00 at display - flashing • Set the current time (CLOCK) immediately to prevent battery exhaustion. About the batteries • Can be used for approximately one year. Observe the following when replacing the batteries • Replace with new batteries of the same type. • Do not use rechargeable batteries (Ni-Cd). • Remove the batteries if the unit is not going to be used for a long period. 1Signal Transmitter 2Operation Display 3Powerful Mode Operation Button 4Room Temperature Setting Button (self-illuminating button) 5Operation Mode Selection Button 6Economy Mode Operation Button 7Auto Airflow Direction Button 8ON-Timer Button 9OFF-Timer Button 0 Reset Point (Press with fine-tipped object to clear the memory) ! OFF/ON Button (self-illuminating button) @ Sleep Mode Operation Button # Fan Speed Selection Button $ Manual Airflow Direction Selection Button % Timer Set Button ^ Timer Cancellation Button & Time-Setting Button * Clock Button ( Remote Control Cover RESETCLOCK OFF CANCEL 1 2 3TIMER ON SET 2 1 1.5V1.5V 5 PREPARATION BEFORE Indoor Unit 1 Connect the power supply cord to an independent power supply 2 Open the front panel 3 Remove the air filters 4 Fit the air purifying filters in place 5 Insert the air filters 6 Close the front panel Remote Control – To set the current time 1 Press 1. 2 Then press 2to increase or decrease the time. 3 Press 1 again. Set time at display will light up. CHECK RESET CLOCK FAN SPEED AIR SWING OFF CANCEL ON SET 1 2 3 TIMER AUTO MANUAL 1 2 6 2 1 45 3 Setting Temperature • Press 3 to increase or • The temperature F ~ 86° F. • Recommended temperature: • During AUTO Operation, press 3 to select:• Operation with 4° F higher than the standard temperature. • Operation with the standard temperature. • Operation with 4° F lower than the standard temperature. Standard Temperature • Once the Automatic Operation is selected, the indoor temperature sensor operates automatically to select the desired operation mode with Cooling or Soft Dry. • After the operation mode has been selected, the mode does not change. HOW TO OPERATE To start the operation • Press 1. • POWER indicator (green) on the indoor unit will light up. • To stop, press once more. Setting Mode • Press 2 to select:AUTO – Automatic Operation COOL – Cooling Operation DRY – Soft Dry Operation FAN – Air Circulation Operation TEMP AUTO AUTUTOFANAN AUTUTO AIR SWING1 2 3 OFF/ON POWERFUL AUTO MANUAL ECONOMY SLEEPON FAN SPEED MODE 235164Cooling Soft Dry 77° F 72° F Operation Standard temperature Indoor temperature 73° F COOL DRY 75° F ~ 78° F 2° F ~ 4° F Lower than the room temperature 5 PREPARATION BEFORE Indoor Unit 1 Connect the power supply cord to an independent power supply 2 Open the front panel 3 Remove the air filters 4 Fit the air purif...

Herunterladen

Geben Sie zwei Ziffern: