Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Anleitung Carrier, modell DWC-092C

Hersteller: Carrier
Dateigröße: 172.1 kb
Dateiname:
Unterrichtssprache:
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Sash Bracket (1 piece) Window Seal A (1 piece) Screw Type B SILL Screw Type A SILL BRACKET 480mm SASH 240mm 610~914mm • Step 3 - Preparation of Chassis 1. Pull the Air-filter out of the Front Grille. 2. Loosen screw which fasten Front Grille with driver. 3. Pull knobs out of the control. (when the knobs are too tight to release, leave them.) 5 6 4. Disassemble Front Grille from Chassis. – Front Grille and chassis are fixed with snap-fit. 1) Release right-lower snap-fit. – Push the right lower side of chassis to the left, with pushing left side of Front Grille to the right until the snap-fit is released. 2) Release left-lower snap-fit. – Push the left-lower side of chassis to the right, with pushing right side of Front Grille to the right until the snap-fit is released. 3) Pull lower side of the Front Grille until it is separated from the chassis. (when knobe remain, pull Front Grille until knobs are released from control) 4) Push base side of the Front Grille to upper side until it is separated from the chassis. 5. After front grille is removed, remove two screws located in both side of chassis and pull out the unit from chassis. Push Push Push Push • Step 4 - Placing Chassis 1. Insert narrow side of ‘Frame Guide Lower’ to rectangle holes located in bottom of chassis, and fasten it with Screw (Type D). 2. Insert Window Kit Frames to Top Guide and Lower Guide. 3. Fasten Shutter to side holes of Chassis with six Screws (Type D). 4. Place the chassis on the window sill and align it with Sill Bracket and sill with Lower Frame Guide and locate window sash to Top Frame Guide. (check the end of chassis for about 1/2 inches (12mm) distance below the level.) 5. Attach the Window seal B to Frame Guide Top. 6. Fasten Front Chassis Bracket to sill with three Screws (Type C). 7. Fasten Sash Bracket with Screw (Type C) to top of indoor window sash or directly into side of window sash or directly into side of window frame. This will prevent raising of the window from the outside. If you have a hard Screw (Type D) wood or metal window frame, a 1/8 inch pilot hole may be needed in order to drive the screws. 8. Attach the Window Seal A to window (see the picture shown in step 8, page 8) FRAME Guide Lower Frame Guide Top Window Seal B Screw (Type D, both side) • Step 5 - Secure Window Shutter Screw (Type C) Screw (Type C) SASH BRACKET CAUTION Do not drill into window sash until window has been inspected to make sure drilling or screw will not damage any locking or lifting mechanism located in the frame. To provide a proper seal, pull each expandable side Window Shutter out and up until it is tight against the window frame. Using the hole in the top and bottom of each Window Kit Frame as a guide, secure Window Kit Frame in window sash and on the window sill. WINDOW KIT FRAME WINDOW SHUTTER WINDOW SASH WINDOW FRAME Screw (Type C) Screw (Type C) INNER WINDOW SILL 7 • Step 6 - Recheck Installation To be sure you have correctly installed y...

Dieses Handbuch ist für folgende Modelle:
Splitgeräte - DWC-072C (172.1 kb)
Splitgeräte - DWC-072C (172.1 kb)
Splitgeräte - DWC-073C (172.1 kb)
Splitgeräte - DWC-073C (172.1 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien