Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 3.26 mb Dateiname: HQ2244UH.pdf Unterrichtssprache:

(Drain hose is not supplied). (See Fig.3) 4. Select the most appropriate connection from among the figures to the right (by considering the hole of the unit) to fit drain pan to your own unit. (See Fig.3) 5. Slide the chassis back into the cabinet. Reinstall the cabinet screws. Secure the cabinet to chassis by using screws. (See Fig.4) 6 About the Controls on the Air Conditioner CLOSE VENT OPEN Part A Part B Drain pipe Drain cap Fig. 4 Fig. 3 Fig. 2 DRAIN HOSE Inside diameter 17mm (5/8") Fig. 1 OFF/ON OPERATION TEMP/TIMER COOL FAN HIGH MED LOW MODE FAN SPEED SET TIMER SET/ CANCEL AIR SWING ECONOMY hr F Wireless Remote Control DRAIN PAN CABINET SCREW Remove the rubber plug OFF/ON OPERATION TEP/TI COOL FAN HIGH MED LOW MOE FAN SPEED SET TIMER SET/ CNE AIR ECONOMY F Wireless Remote Control NOTE: Before using the ventilation feature, and prior to installing the front grille, pull down part until level with part . 7 About the Controls on the Air Conditioner Air Filter Cleaning The air filter behind the front grille should be checked and cleaned at least once every 2 weeks or more often if necessary. The grille is designed to clean the filter both upward and downward. TO REMOVE: 1. Open the inlet grille upward by pulling out the bottom of the inlet grille or downward by pulling out the top of the inlet grille. 2. Using the tab, pull up slightly on the filter to release it and pull it down or up. 3. Clean the filter with warm, soapy water under 40°C (104°F). 4. Rinse and gently shake the water from the filter and let it dry before replacing it. CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. Care and Maintenance TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET. 8 Features and Installation Learning parts name prior to installation will help you understand the installation procedure. Features Features CABINET FRONT GRILLE AIR FILTER AIR INTAKE (INLET GRILLE) AIR DISCHARGE HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER) VERTICAL AIR DEFLECTOR (HORIZONTAL LOUVER) EVAPORATOR CONTROL BOARD POWER CORD BASE PAN CONDENSER COMPRESSOR BRACE REMOTE CONTROLLER Installation About 1/2" Over 20" HEAT RADIATION FENCE AWNING INSIDE OUTSIDE FOAM COOLED AIR 30-60" Level 1/4 Bubble How to Install the Unit 1. To avoid vibration and noise, make sure the unit is installed securely and firmly. 2. Install the unit where the sunlight does not shine directly on the unit. If the unit receives direct sunlight, build an awning to shade the cabinet. 3. There should be no obstacle, like a fence, within 20” which might restrict heat radiation from the condenser. 4. To prevent reducing performance, install the unit so that louvers of the cabinet are not blocked. 5. Install the unit a little obliquely outward not to avoid leaking the condensed water into the room (about 1/2” or 1/4 bubble with level). 6. Install the unit with its bottom portion 30~60” above the floor level. 7. Stuff the foam between the top of the unit and the wall to prevent air and insects from getting into the room. 8. The power cord must be connected to an independent circuit. The green wire must be grounded. 9. Connect the drain tube to the base pan hole in the rear side if you need to drain (consult a dealer.) Plastic hose or equivalent may be connected to the drain tube. Window Requirements NOTE: All supporting parts should be secured to firm wood, masonry, or metal. WINDOW REQUIREMENTS 1. This unit is designed for installation in standard double hung windows with actual opening widths from 26" to 41". The top and bottom window sashes must open sufficiently to allow a clear vertical opening of 18" from the bottom of the upper sash to the window stool. 2. The stool offset (height between the stool and sill) must be less than 1 1/4". 26" to 41" 18" min Offset Sill Exterior Interior wall Stool Features and Installation 9 Installation Kits Contents Features and Installation Foam-PE (Adhesive-Backed) Foam-PE (Adhesive-Backed) Type C (5) Type D (2)Type A (14) Carriage Bolt (2) Lock Nut (4) Type B (7) Foam strip (Plain-Back) Right frame curtain Drain pipe Window locking bracket Left frame curtain Sill bracket(2) Support bracket(2) Top retainer bar is in product package. 10 11 Features and Installation Foam-PE Top retainer bar Top retainer bar Foam-PE Screw (Type A) Screw(...

Herunterladen

Geben Sie zwei Ziffern: