Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Asus, modell 370698-002

Hersteller: Asus
Dateigröße: 1.22 mb
Dateiname: 3ddb91d5-c120-4e85-8606-1d5652b46a8b.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

. If you have problems making this connection, go to the device manufacturer Web site for the latest version of the driver for the device. Installing Additional RAM (Memory) The notebook has 2 slots that hold 2 RAM modules. At least one slot contains a RAM module installed at the factory. You can use both slots to expand your RAM. To Install a RAM Expansion Module Use only PC2100 DDR-266-MHz or higher RAM. You will need a small Phillips screwdriver for these steps. A CAUTION: The internal components of your notebook are extremely sensitive to static electricity and can be permanently damaged by it. Handle the RAM module only by its edges. Before installing the memory module, discharge static electricity by touching the metal shielding around the connectors on the back of the notebook. 1.Save your work and shut down the notebook. If you are not sure whether the notebook is off or in Hibernation, briefly press the power button. If your work returns to the screen, save your work, exit all applications, and then shut down the notebook. 2.Disconnect all external devices connected to the notebook. 3.Disconnect the power cord 4.Remove the battery pack. 5.Turn the unit bottom-side up, loosen the screws holding the RAM cover, then remove the cover. 6.Match your notebook to the following illustration. Insert the RAM board into the connector at about a 30-degree angle until it is fully inserted. Then press down at both sides until both latches snap closed. 7.Replace the cover. 8.Insert the battery pack. To Remove a RAM Expansion Module You may want to remove a RAM module so you can install a larger one. You will need a small Phillips screwdriver for these steps. A CAUTION: Your notebook internal components are extremely sensitive to static electricity and can be permanently damaged by it. Handle the RAM module only by its edges. Before installing the memory module, discharge static electricity by touching the metal shielding around the connectors on the back of the notebook. 1.Save your work and shut down the notebook. If you are not sure whether the notebook is off or in Hibernation, briefly press the power button. If your work returns to the screen, save your work, exit all applications, and then shut down the notebook. 2.Disconnect all external devices connected to the notebook. 3.Disconnect the power cord 4.Remove the battery pack. 5.Turn the unit bottom-side up, loosen the screws holding the RAM cover, then remove the cover. 6.Match your notebook to the following illustration. Release the 2 latches at the sides of the RAM board, so the free edge of the board pops up. 7.Pull the board out of the connector. 8.Replace the cover. 9.Insert the battery pack. Replacing the Hard Drive To Replace the Hard Drive You will need a small Phillips screwdriver for this procedure. 1.Save your work and shut down the notebook. If you are not sure whether the notebook is off or in Hibernation, briefly press the power button. If your work returns to the screen, save your work, exit all applications, and then shut down the notebook. 2.Disconnect all external devices connected to the notebook. 3.Disconnect the power cord 4.Remove the battery pack. 5.Turn the unit bottom-side up. 6.Match your notebook to the following illustration. Use a pointed tool to remove the plugs from the 2 or 3 screw holes, then remove the screws. The number of screws varies by model. 7.Gently pull the hard drive out of the notebook. 8.Gently slide the new drive into the hard drive compartment. Press firmly to make sure the connector seats properly. 9.Reinstall the hard drive screws and plugs. . If you are installing a new hard drive, you should create a Utility partition on the drive before loading any software. To Replace the Hard Drive Holder If you are installing a new hard drive that does not have a holder, you can remove the holder parts from the hard drive you are removing. You will need a small Phillips screwdriver for this procedure. 1.Remove the 4 screws from the sides of the holder and drive case, then slide the drive out of the holder. 2.Notice that the hard drive has a pin connector attachment at one end. Carefully remove this connector from the end of the drive. Work alternately at each end so that the connector slides off evenly without bending the connector pins. 3.Carefully put the pin connector attachment back onto the pins on the end of the new hard drive. Work alternately at each end so that the connector slides on evenly without bending the connector pins. 4.Insert the drive into the holder. 5.Reinstall the screws into the holder and drive case. To Prepare a New Hard Drive When you install a new hard drive, you also need to prepare it to be able to work with your notebook. If you want to restore the Windows software and operating system that were originally installed on your notebook, follow the system recovery procedures described in the “Troubleshooting” chapter of this guide. Troubleshooting Troubleshooting Your Notebook This chapter cont...