Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
PC Desktops - HP Integrity NonStop H-Series (16.73 mb)
PC Desktops - HP Integrity NonStop H-Series (957.56 kb)
PC Desktops - HP Integrity NonStop H-Series (881.66 kb)
PC Desktops - HP Integrity NonStop H-Series (965.62 kb)
PC Desktops - HP Integrity NonStop H-Series (676.93 kb)
PC Desktops - HP Integrity NonStop H-Series (393.72 kb)
PC Desktops - HP Integrity NonStop H-Series (776.57 kb)
Anleitung Zusammenfassung
readme-v2.fm Page 3 Monday, November 13, 2000 1:52 PM
Make Sure the Configurations Match. Because of these default configuration and full-duplex
considerations, for best operation, you should make sure that the devices connected to the trans-
ceiver ports are configured the same as the default configurations shown above. At minimum, make
sure the configurations match. Note that for the Series 2300 switches, there is no console port, so
the configuration cannot be altered, and you must change the configuration on the connected device
to match the default configuration on your switch ports.
Changing Connection Speeds to the 100/1000-T Transceiver. If you connect the 100/1000-T
transceiver to a device that operates at one speed (for example 100 Mbps), and subsequently
disconnect from that device and connect to a device that operates at a different speed (for example
1000 Mbps), you must reset the Series 2300 or 2500 switch for the new speed to take effect. Until you
reset the switch, in some cases the link will not complete; in other cases the link will complete but
at the former speed. For example, when changing from a 100 Mbps connection to a connection with
a 100/1000Base-T device, you may get a completed link, but it will be operating at the old speed—
100 Mbps.
Manual Changes:
To correct your switch Installation and Getting Started Guide (5969-2353) relative to the above
information, please keep the following information with the guide and note the pages where this
information applies:
Page 3-2 — change the bulleted item titled “Connecting to devices that have a fixed full-duplex
configuration” to the following:
I
Connecting to devices that have a fixed configuration:
•
Connecting with the fixed RJ-45 ports: The Series 2300 and 2500 fixed RJ-45 ports
have a default configuration of Auto. That is, when connecting to attached devices, the
switch will operate in one of two ways to determine the link speed and the communica-
tion mode (half duplex or full duplex):
–
if the connected device is also configured to Auto, the switch will automatically negotiate
link speed, communication mode, and flow control and a valid link should occur
–
if the connected device has a fixed configuration, for example 100 Mbps, at half or full
duplex, the switch will automatically sense the link speed, but will default to a communi-
cation of half duplex
Because the Series 2300 and 2500 switches behave in this way (in compliance with the IEEE
802.3 standard), if a device connected to the switch’s fixed RJ-45 ports has a fixed
configuration at full duplex, a duplex mismatch occurs between the switch and the
connected device. The result will be high error rates and very inefficient communications
between the switch and the device.
Make sure that all devices connected to the fixed RJ-45 ports on the Series 2300 and 2500
switches are configured to auto negotiate, or are configured to connect at half duplex (all
hubs are configured this way, for example).
3
...Dieses Handbuch ist für folgende Modelle:
PC Desktops - HP Integrity NonStop J-Series (161.12 kb)
PC Desktops - HP NonStop G-Series (161.12 kb)
PC Desktops - HP NonStop L-Series (161.12 kb)