Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA. - 2 !! CAUTION 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2. Take care when using cleaning agents or detergents. 3. Avoid using food products that produce flames under the Range Hood. 4. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 5. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 6. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. 7. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a maximum of 30" above the cooking surface. 8. Two installers are recommended because of the large size and weight of this hood. 9. This product is equipped with a thermostat which may start blower automatically. To reduce the risk of injury and to prevent power from being switched on accidentally, switch power off at service panel and lock or tag service panel. 10. Please read specification label on product for further information and requirements. - 3 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag (B080810495) containing: 2 - Mounting Brackets 1 - Flue Mounting Bracket 8 - Mounting Screws (4,8 x 38mm Pan Head) 4 - Mounting Screws (3,9 x 9,5mm Pan Head) 8 - Drywall Anchors 1 - Installation Instructions 1 - Warranty Card MOUNTING DECORATIVE BRACKETS FLUE 4 MOUNTING SCREWS (3,9 x 9,5mm Pan Head) FLUE MOUNTING BRACKET 8 DRYWALL ANCHORS 8 MOUNTING SCREWS (4,8 x 38mm Pan Head) - 4 INSTALL THE DUCTWORK NOTE: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. Larger ducting may be required for best performance with longer duct runs. 4. Install a roof or wall cap. Connect round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. INSTALL MOUNTING ROOF CAP ROUND DUCT WALL CAP ROUND ELBOW HOOD DECORATIVE FLUE 24” TO 30” ABOVE COOKING SURFACE 6” ADAPTER FRAMING BEHIND DRYWALL BRACKETS 1. Construct wood wall framing that is flush with interior surface of wall studs.Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting brackets to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mount31- 3/4"= bottom of hood 24" above cooktop ing brackets to framing using dimensions 37-11/16"= bottom of hood 30" above cooktop shown. NOTE: On 8’ ceilings, the hood distance above cook top is minimum 24”, maximum 27”. - 5 INSTALL THE HOOD RECTANGULAR MOUNTINGBRACKETSMOUNTING CUTOUTS 1. Hang the hood from the brackets through the rectangular cut-outs on the back of the hood. Cut-outs are larger than the brackets to allow for horizontal adjustment. The bottom of the hood should be 24" to 30" above the cooking surface. 2. Height adjustment screws provide vertical adjustment. SCREWS WALL (4.8x38mm) 3. Depth adjustment screws provide hori-FRAMING zontal adjustment. DEPTH ADJUSTMENT 4. Secure the hood with mounting screws HEIGHT SCREWS (4.8x38mm). Use drywall anchors, provided, if wall studs or framing are not available. MOUNTING SCREWS ADJUSTMENT SCREWS (4.8x38mm) WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. 33-7/16” (85cm) max WARNING - Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly g...