Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Step 3 Unlock the screw on the riser bracket to remove the PCI bracket. Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Reverse step 1 to 3 to reinstall riser bracket into the system module. 1 2 3 3 16 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 3 Slide hard disk into blank. Step 4 Secure it with screws. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 4 4 17 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Pull up the cabled and align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. Step 2 Please push the cables into the gap between fan duct and power supply. 1 Guiding groove 18 GS-R1271-RH Rack Mount Server 3-1: Front View of GS-R1271-RH Chapter 3 Appearance of GS-R1271-RH .. .. .. .. .. .. .. .. Standard DVD-COMBO Hot-Swap SATA HDDs USB connectors .. Front panel switch and LEDs VGA port .. System Appearance 3-2: Rear View of GS-R1271-RH .......... • • Power • Mouse connector • Keyboard connector • COM port • VGA port • USB connectors • RJ45 LAN ports • Low-profile riser slot • Full-height riser slot 19 GS-R1271-RH Rack Mount Server 3-3: Switch and LED Indicators Introduction ID LED NMIHDD LAN1/2 LED ID SwitchError ID21NMIID Power Button NameColor Condition Description PowerGreen On Power On Green Blink Sleep (S1) -Off Power Off (S4/S5) HDDGreen Blink Hard Disk Drive Access -Off No Access and No HDD Fault IDBlue On Unti selected for identification (Identification)-Off No identification Error Yellow On IPMI shows the event log. -Off No event log in IPMI 20 System Appearance 3-4: LAN LED Description NameColor Condition Description LANGreen O N LAN Link / no Access Link/ActivityGreen BLINK LAN Access -OFF Idle GbE LANYellow O N 1Gbps connection Speed Yellow BLINK Port identification with 1Gbps connection Green O N 100Mbps connection Green BLINK Port identification with 10 or 100Mbps connection -OFF 10Mbps connection 21 GS-R1271-RH Rack Mount Server 3-5: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 Motherboard Layout Chapter 4 Motherboard Jumper Setting 4-1: GA-7NCSV1-RH Motherboard Jumper Setting 1 3 4 2 7 8 6 5 1. CLR_CMOS1 5. SPI_WP1 2. PWR_JP1 6. RECOVERY1 3. PILOT_DIS 7. PASSWORD1 4. BMC_SEL1 8. System Identify 23 GS-R1271-RH Rack Mount Server 1. CLR_CMOS ( (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1-2 Close: Normal operation (Default setting) 1 2-3 Close: Clear CMOS 2. PWR_JP1 (Front panel USB1 power source selection jumper) 1 1-2 Close: 5V_AUX 2-3 Close: 5V 1 3. PILOT_DIS (Pilot II BMC Function Enable/Disable jumper) 1 1-2 Close: Enable Pilot II BMC function 1 2-3 Close: Disable Pilot II BMC function 4. BMC_SEL1 (BMC Firmware area selection) 1 1-2 Close: Select BMC firmware in bank0 1 2-3 Close: Select BMC firmware in bank1 5. SPI_WP1 (SPI BIOS write protection Disable/Enable jumper) 1 1-2 Close: Select BMC firmware in bank0 1 2-3 Close: Select BMC firmware in bank1 24 Jumper Setting 6. RECOVERY1 (BIOS recovery jumper) 1 1-2 Close: Normal operation(Default setting) 1 2-3 Close: Enable BIOS Recovery function. 7. PASSWORD1 (Skip password jumper) 1 1-2 Close: Normal operation. (Default setting) 1 2-3 Close: Clear Supervisor Password in BIOS setup menu. 8. Ssystem Identify (System Identify Enable/Disable jumper) 1 1-2 Close: Enable System Identify function. (Default setting) 1 2-3 Close: Disable System Identify function. 25 BIOS Setup Chapter 5 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERING SETUP When the power is turned on, press the