CONFIRMED 4. Please note: To re-program temperature and coffee strength see chapter T. O) Installing and Activating the Clearyl Cartridge. (watch DVD for details) Rinse cartridge under running water. Attach extension rod. Remove water tank (empty), pull up cartridge holder lid and install the cartridge to fit snugly inside the fins. Close cartridge holder lid and fill tank with water and replace. You MUST ACTIVATE the filter NOW! COFFEE READY. Push and hold the Rotary Dial until you hear a beep.

Watch the DVD instructions! Traces of Coffee Grounds in New Machine? This is normal! Grinder was tested during assembly with beans. Despite cleaning, traces of ground coffee may be found. RED TEXT represents display text. Illustration numbers on next page correspond with Operating Instructions. A) First Time Ever Preparation 1. Fill water in tank, open Cover Lid (spring activated!), remove Bean Container Safety Lid and add beans. Only regular beans, no flavored or coated beans!!! Replace Bean Co

5. Add the correct amount of ground coffee (chapter 5c). 6. Close the water container lid. 7. MT600 (Thermal Carafe): Make sure the thermal carafe is empty and the lid of the thermal carafe is completely closed (Fig. 11). MG600 (Glass Carafe): Make sure the lid sits properly on the glass carafe. Insert the carafe into the machine. 8. Turn the machine on (Fig. 2, N). 9. Never open the water container lid as long as coffee is brewing. Hot water could spill out causing burns. Wait until the brewing

If you make coffee twice a day, the light will flash after 30 days. If you make coffee three times a day, the light will flash after 20 days. This will help you to plan the right amount of cartridges. Attention: When you unplug the machine for more than 10 seconds or if you have a power failure, the electronic indicator loses its memory. Then it is best to replace the filter 6 weeks after first use. Caution: Once the cartridge is activated you should never use it for longer than six weeks. Harmf

Caution: Never open the water container lid during brewing. 5f. Serving Coffee Brewing time for a full pot of coffee takes just about 7 minutes. Then all the water is passed through the heat 9 ing element and the internal thermostat shuts off. The red indicator light still stays on for approx. another two minutes then turns off, too. This is normally the time it takes for all the water in the filter holder to pass into the carafe. Depending on the amount of coffee and the fineness of the grind t

11 a. How to Decalcify with White Vinegar ......................................... 11 b. Using other Decalcifying Agents ............................................... 11 11. Troubleshooting .............................................................................. 11 12. How to Contact Jura-Capresso ................................................... 12 13. Customer Service .......................................................................... 12 14. Limited One Year Warranty ........

Turning the Machine On ......................................13 7. Adjusting the Grinder ..............................................14 8. DAILY PREPARATION ............................................14 Page 9. One-Touch Beverage Buttons .................................14 10. Brewing Coffee and Espresso..............................14 11. Overriding Strength and Cup Size during Brewing....15 12. Auto Cappuccino System .......................................15 13. Cappuccino and Latte........

15.8 PROGRAMMING ECONOMY MODE In the setting ECONOMY MODE ON the heating element for steam turns off 10 minutes after last use of steam. In the setting ECONOMY MODE OFF the heating element for steam turns off 20 minutes after last use of steam. Whenever the heating element is off the green indicator lights inside the steam buttons are off. COFFEE READY • Press the P button. POWDER QUANTITY / PRESS KEY • Press the + button until the display shows ECONOMY MODE OFF • Press the P button. • Press the

16.6 REMOVING STONES OR OTHER FOREIGN OBJECTS FROM THE BURR GRINDER If the burr grinder is blocked, proceed as follows: • Turn off the machine by pushing the ON/OFF button (Fig. 2,B). Wait until the machine has shut down completely. • Unplug the machine. • Open the bean container and remove all beans (scoop out beans or use a hand-held vacuum cleaner). • Loosen the two screws in the bean container (Fig.24) and remove the bean container (Fig.25). • If any beans remain, remove them. • Attach the b

Shake off any access water and wait for one minute. • If all five fields of the test stick turn reddish, set the hardness level to 4. If four fields turn reddish, set the hardness level to 3. If three or less fields turn reddish, leave the level in position 2. You can change the hardness settings as follows: COFFEE READY • Open cover for programming buttons (Fig.1,19) and press and hold the P button (Fig.3A,P) until you hear a beep. PRESS KEY / POWDER QUANTITY • Press the + button several times