Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Yellow Green DESCALING The descaling process takes approx. 35 minutes. Limescale builds up inside the machine during use. It needs to be removed regularly as it may clog the water and coff ee circuit of your machine. The machine tells you when descaling is needed. If the machine display shows the CALC CLEAN icon, it means that you need to descale. Caution: Not doing this will ultimately make your machine stop working properly, and in this case repairing is NOT covered by your warranty. 46 ENGLISH 2 Remove the Classic Milk Frother from the steam/hot water wand. 3 Remove the “INTENZA+” water fi lter from the water tank if it was installed and replace it with the small white original one. Place the water tank back into the machine. Yellow 4 Press the “ ” MENU button and scroll the pages by pressing the “ ” MENU button until the following icon is displayed. 5 Press the “ ” button to start the descaling process. Green Warning: Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end. Never use vinegar as a decalcifi er. Note: During the descaling cycle do not switch off the machine. If this has happened you have to restart the descaling cycle to fully complete it. It will restart from the point the descaling cycle had previously been left. To perform the descaling cycle, follow the steps below: Before descaling: 1 Empty the drip tray. Use the Descaling solution only. Its formula has been designed to ensure better machine performance. You can purchase separately the Descaling solution. Please refer to the maintenance products page in this user manual for further details. ENGLISH 47 Note: If you press the “ ” button by mistake, press the “ ” button to quit. 6 Remove the water tank and pour the entire content of the descaling solution. Then fi ll the water tank with fresh water up to the CALC CLEAN level. 7 Place the water tank back into the machine. Yellow 8 Place a large container (1.5 l) under both the steam/hot water wand and the dispensing spout. 9 Press the “ ” button to start the descaling cycle. 10 The machine will start dispensing the descaling solution at intervals. . The bar on the display shows the cycle progress. Yellow Yellow 48 ENGLISH Note: The descaling cycle may be paused by pressing the “ ” button .To resume the cycle, press the “ ” button again. This allows you to empty the container or to stay away from the machine for a brief period of time. 11 When this icon is displayed, the water tank is empty. 12 Remove and empty the container. 13 Empty the drip tray and place it back. 14 Remove the water tank, rinse it and fill it up to the MAX level with fresh water. Place it back into the machine. When inserting the water tank into the machine, the display on the left is shown. 15 Put the container back under both the steam/hot water wand and the dispensing spout. 16 Press the “ ” button to start the rinsing cycle. Yellow Red Yellow Red 17 When this icon is displayed, the water tank is empty. Repeat steps 12 to 16. Then go to step 18. ENGLISH 49 Yellow 20 When the amount of water needed for the rinse cycle has been completely dispensed, this icon on the side is displayed. Press the " " MENU button to quit the descaling cycle. 21 Press the“ ” button to prime the circuit. 22 The machine now carries out the warm-up and automatic rinse cycle to prepare for product brewing. Green 18 When the water tank is empty, remove the water tank, rinse it and fi ll it up to the MAX level with fresh water. Place it back into the machine. 19 Empty the container and place it back under under both the steam/hot water wand and the dispensing spout. 23 Remove and empty the container 24 Empty the drip tray and place it back. 25 The descaling cycle is now complete. 26 Remove the small white water fi lter and place back the “INTENZA+” water fi lter into the water tank if it was installed and the Classic Milk Frother. Note: At the end of the descaling cycle, wash the brew group as described in the “Weekly Cleaning of the Brew Group” chapter. The two rinse cycles are performed in order to have the circuit cleaned with a preset amount of water and ensure proper machine operation. If the water tank is not fi lled up to MAX level, the machine might require three or more cycles. 50 ENGLISH PROGRAMMING You can adjust the machine functions to your personal preference by accessing the program menu. The following parameters can be adjusted Coff ee temperature This function allows you to adjust the coffee brewing temperature. Coffee bean selection This function allows you to optimize the grinding for selected type of coffee bean. Coffee duct emptying cycle. This function allows you to empty the coffee duct and grinder before changing coff ee beans. Yellow YellowYellow Yellow Water hardness This function allows you to adjust the water hardness setting according to the area where you live. 1 = very soft water 2 = soft water 3 = hard water 4 = very hard water For more details please see the ...